CONSTRUCTION
Multi-information Display
Display Function Flow
The multi-information display can be switched as shown in the flow chart below:
| *a | Conditions are not met. |
| *b | Conditions are met. |
| *c | If there are multiple display requests, items will be displayed in sequence. |
| *d | Item or display is selected by operating the steering pad switch assembly. |
| *e | ODO display is displayed for a certain period of time after the ignition switch is turned off. |
| *f | Ignition switch off to ON. |
| *g | Ignition switch ON to off (conditions are not met). |
| *h | Ignition switch ON to off (conditions are met). |
Display Tab Operation
The information currently displayed can be switched using the LEFT/RIGHT switch*1 or UP/DOWN switch*2 of the steering pad switch assembly.
*1: Models with analog meter
*2: Models with digital meter
| *a | Fuel Economy Tab | *b | Driving Assist System Information Tab |
| *c | Audio Information Tab | *d | Vehicle Information Tab |
| *e | Settings Tab | *f | Warning Message Tab |
| *g | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
|
RIGHT switch (analog meter) or DOWN switch (digital meter) operation |
|
LEFT switch (analog meter) or UP switch (digital meter) operation |
Setting Function
The items displayed on the multi-information display can be customized.
The following items can be selected on the information setting screen.
| Item | Available Setting |
|---|---|
| Clock Setting | ·
Sets the minute display to "00" via the enter switch on the steering pad switch.
·
Clock display can be changed: -
12H -
24H ·
Adjust Clock |
| Item | Available Setting | |
|---|---|---|
|
*: Models with steering vibration function |
||
| LTA | Lane Center | Center trace function can be set to on/off: -
ON -
OFF |
| Alert* | Setting for warning method can be changed: -
Steering Wheel Vibration (Icon is displayed) -
Buzzer (Icon is displayed) |
|
| Sensitivity | Sensitivity of alert system can be changed: -
High (Icon is displayed) -
Standard (Icon is displayed) |
|
| Sway Warning | Sway warning function can be set to on/off: -
ON -
OFF |
|
| Sway Sensitivity | Sway warning sensitivity can be selected: -
High (Icon is displayed) -
Standard (Icon is displayed) -
Low (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
| PCS | The pre-collision system can be set to on/off: -
ON -
OFF |
|
| Sensitivity | Pre-collision system warning sensitivity can be selected: -
Early (Icon is displayed) -
Middle (Icon is displayed) -
Late (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
|
*: Models with rapidly approaching vehicle detection |
||
| BSM | The blind spot monitor system can be set to on/off: -
ON -
OFF |
|
| Brightness | Brightness of the outer rear view mirror indicator light can be changed: -
Bright (Icon is displayed) -
Dim (Icon is displayed) |
|
| Sensitivity* | Blind spot monitor system sensitivity can be selected: -
Early (Icon is displayed) -
Middle (Icon is displayed) -
Later (Icon is displayed) -
Only blind spots (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
| Toyota Parking Assist-sensor System | The Toyota parking assist-sensor system can be set to on/off: -
ON -
OFF |
|
| Volume | The volume of the warning buzzer can be selected: -
1 (Icon is displayed) -
2 (Icon is displayed) -
3 (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
| Rear Cross Traffic Alert System | The rear cross traffic alert system can be set to on/off: -
ON -
OFF |
|
| Volume | The volume of the warning buzzer can be selected: -
1 (Icon is displayed) -
2 (Icon is displayed) -
3 (Icon is displayed) |
|
| Item | Available Setting |
|---|---|
| PKSB | The parking support brake system can be set to on/off: -
ON -
OFF |
| Item | Available Setting | |
|---|---|---|
| HUD | The head-up display function set to on/off -
ON -
OFF |
|
| Brightness/Position | The brightness and position of the head-up display can be selected: -
Bright (Graphic is displayed) -
Dark (Graphic is displayed) -
High -
Low |
|
| HUD Display Customize | The contents displayed in the head-up display can be selected: -
Tachometer |
|
The contents of the tachometer can be selected: (a)
Blank (b)
Hybrid system indicator (c)
Eco indicator (d)
Tachometer -
Navigation The navigation function display can be set to on/off. (1)
ON (2)
OFF -
Driving support The driving support function display can be set to on/off. (1)
ON (2)
OFF -
Compass The compass display function display can be set to on/off. (1)
ON (2)
OFF -
Audio The audio display function display can be set to on/off. (1)
ON (2)
OFF |
||
| HUD Rotation | The tilt of the HUD image can be changed: -
Clockwise -
Counterclockwise |
|
| Item | Available Setting | |
|---|---|---|
| RSA | The road sign assist system can be set to on/off: -
ON -
OFF |
|
| Notification Method* | Notification method can be selected: -
Above Speed Limit: (1)
No Notification (2)
Only visual (3)
Visual & Audio -
Overtaking: (1)
No Notification (2)
Only visual (3)
Visual & Audio -
Others: (1)
No Notification (2)
Only visual (3)
Visual & Audio |
|
| Notification Level* | Excess speed notification level can be selected: -
10 km/h (5 mph) -
5 km/h (3 mph) -
2 km/h (1 mph) Excess speed notification level can be selected: -
5 km/h -
3 km/h -
1 km/h |
|
*: Available settings differ by destination.
| Item | Available Setting |
|---|---|
| Dynamic Radar Cruise Control with Road Sign Assist | The dynamic radar cruise control with road sign assist system can be set to on/off: -
ON -
OFF |
| Item | Available Setting | |
|---|---|---|
|
*: Models with tire pressure warning system |
||
| Rear Seat Reminder | The rear seat reminder system can be set to on/off: -
ON -
OFF |
|
| TPWS* | Set Pressure | The tire pressure warning system can be initialized. |
| Change Wheel | The tire pressure warning system ID can be selected. | |
| Setting Unit | The unit displayed on the multi-information display can be selected: -
kPa -
psi -
bar |
|
| Item | Available Setting | |
|---|---|---|
|
*1: Gasoline models *2: HV models *3: Models with navigation system *4: Models with stop and start system *5: Models with voice recognition system *6: 3 Door Models |
||
| Language | The language used on the multi-information display can be selected: -
Arabic -
Czech -
Danish -
German -
Greek -
English -
Spanish -
Flemish -
French -
Italian -
Romanian -
Hungarian -
Dutch -
Norwegian -
Polish -
Portuguese -
Russian -
Slovak -
Finnish -
Swedish -
Turkish -
Ukrainian -
Hebrew
|
|
| Units | The unit displayed on the multi-information display can be selected: -
km (km/L) -
km (L/100 km) -
miles (MPG)
|
|
| Eco Indicator*1 | The eco indicator can be set to on/off: -
ON -
OFF |
|
| EV indicator*2 | The EV indicator can be set to on/off: -
ON -
OFF |
|
| Fuel Economy Tab | Hybrid System*2 | The eco guidance can be set to on/off: -
ON -
OFF |
| Fuel Economy | The fuel economy type can be selected: -
Trip Average -
Total Average -
Tank Average |
|
| Vehicle Information Tab | Display Contents | The following displays can be switched to on/off: -
Energy Monitor*2 -
AWD Monitor*6 |
| Drive Info Type | The drive information type can be selected: -
Trip -
Total |
|
| Drive Info Items | The upper and lower of drive information items can be selected: -
Average Vehicle Speed -
Distance Travelled -
Elapsed Time |
|
| Pop-Up Display | The following displays that appear as soon as the set conditions are met can be switched to on/off: -
Turn-by-turn Navigation*3 -
Telephone -
Audio Operation -
Volume Operation -
Voice Control*5 -
Fuel Price -
Duration*4 -
Status*4 -
Brightness |
|
| Multi-information Display OFF | Multi-information display is turned off. | |
| Default Settings | The set items can be initialized. | |
Interruption Display
When a warning is necessary, the warning message interrupts the current display on the multi-information display.
A warning message is displayed via an interrupt display when a vehicle malfunction occurs to warn the driver. Also, an advice message is displayed via an interrupt display depending on the situation, such as when the driver must proceed with caution.
The buzzer in the combination meter assembly may sound depending on the item displayed on the multi-information display.
The intersection guidance*, telephone display, audio operation and volume operation displays are linked with the multimedia system or navigation system and displayed via an interrupt display.
*: Models with navigation system
The combination meter assembly displays the following messages based on signals received from the hybrid vehicle control ECU.
| Message | Buzzer |
|---|---|
|
*1: This message is displayed together with one of the listed messages. *2: AWD Models |
|
| CDY-2 | - |
| CDY-4*2 | - |
| CDY-2E | - |
| CDY-4E*2 | - |
| RES-1 | - |
| RES-2 | - |
| RESOLVER-1 NOT ADJUSTED | - |
| RESOLVER-2 NOT ADJUSTED | - |
| RESOLVER-R NOT ADJUSTED | - |
| Shift to P Before Exiting Vehicle | Sounds |
| Hybrid System Malfunction Do Not Tow This Vehicle | Sounds |
| Shift is in N Release Accelerator Before Shifting*A
Shift Out of N Release Accelerator Before Shifting*A |
Sounds |
| Press Brake when Vehicle is Stopped Hybrid System may Overheat | Sounds |
| Traction Battery Needs to be Protected Shift into P to Restart | Sounds |
| Hybrid System Malfunction*1
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
Stop in a Safe Place See Owner's Manual ·
Stop in a Safe Place within 0.3 miles*A ·
Stop in a Safe Place within 0.5 km (0.3 miles)*A ·
Stop in a Safe Place within 0.6 miles*A ·
Stop in a Safe Place within 1.0 km (0.6 miles)*A ·
Stop in a Safe Place within 0.9 miles*A ·
Stop in a Safe Place within 1.5 km (0.9 miles)*A ·
Stop in a Safe Place within 1.2 miles*A ·
Stop in a Safe Place within 2.0 km (1.2 miles)*A ·
Stop in a Safe Place within 3.1 miles*A ·
Stop in a Safe Place within 5.0 km (3.1 miles)*A ·
Stop in a Safe Place within 6.2 miles*A ·
Stop in a Safe Place within 10 km (6.2 miles)*A ·
Output Power Reduced Avoid Shifting to N ·
Avoid Shifting to N Visit Your Dealer ·
Hybrid System Stopped Stop in a Safe Place ·
Shift to P See Owner's Manual |
Sounds |
| Check Engine*1
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
Stop in a Safe Place See Owner's Manual ·
Stop in a Safe Place within 0.3 miles*A ·
Stop in a Safe Place within 0.5 km (0.3 miles)*A ·
Stop in a Safe Place within 0.6 miles*A ·
Stop in a Safe Place within 1.0 km (0.6 miles)*A ·
Stop in a Safe Place within 0.9 miles*A ·
Stop in a Safe Place within 1.5 km (0.9 miles)*A ·
Stop in a Safe Place within 1.2 miles*A ·
Stop in a Safe Place within 2.0 km (1.2 miles)*A ·
Stop in a Safe Place within 3.1 miles*A ·
Stop in a Safe Place within 5.0 km (3.1 miles)*A ·
Stop in a Safe Place within 6.2 miles*A ·
Stop in a Safe Place within 10 km (6.2 miles)*A ·
Output Power Reduced Avoid Shifting to N ·
Avoid Shifting to N Visit Your Dealer ·
Hybrid System Stopped Stop in a Safe Place ·
Shift to P See Owner's Manual |
Sounds |
| Hybrid Battery System Malfunction*1
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
Stop in a Safe Place See Owner's Manual ·
Stop in a Safe Place within 0.3 miles*A ·
Stop in a Safe Place within 0.5 km (0.3 miles)*A ·
Stop in a Safe Place within 0.6 miles*A ·
Stop in a Safe Place within 1.0 km (0.6 miles)*A ·
Stop in a Safe Place within 0.9 miles*A ·
Stop in a Safe Place within 1.5 km (0.9 miles)*A ·
Stop in a Safe Place within 1.2 miles*A ·
Stop in a Safe Place within 2.0 km (1.2 miles)*A ·
Stop in a Safe Place within 3.1 miles*A ·
Stop in a Safe Place within 5.0 km (3.1 miles)*A ·
Stop in a Safe Place within 6.2 miles*A ·
Stop in a Safe Place within 10 km (6.2 miles)*A ·
Output Power Reduced Avoid Shifting to N ·
Avoid Shifting to N Visit Your Dealer ·
Hybrid System Stopped Stop in a Safe Place ·
Shift to P See Owner's Manual |
Sounds |
| Accelerator System Malfunction*1
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
Stop in a Safe Place See Owner's Manual ·
Stop in a Safe Place within 0.3 miles*A ·
Stop in a Safe Place within 0.5 km (0.3 miles)*A ·
Stop in a Safe Place within 0.6 miles*A ·
Stop in a Safe Place within 1.0 km (0.6 miles)*A ·
Stop in a Safe Place within 0.9 miles*A ·
Stop in a Safe Place within 1.5 km (0.9 miles)*A ·
Stop in a Safe Place within 1.2 miles*A ·
Stop in a Safe Place within 2.0 km (1.2 miles)*A ·
Stop in a Safe Place within 3.1 miles*A ·
Stop in a Safe Place within 5.0 km (3.1 miles)*A ·
Stop in a Safe Place within 6.2 miles*A ·
Stop in a Safe Place within 10 km (6.2 miles)*A ·
Output Power Reduced Avoid Shifting to N ·
Avoid Shifting to N Visit Your Dealer ·
Hybrid System Stopped Stop in a Safe Place ·
Shift to P See Owner's Manual |
Sounds |
| Hybrid System Stopped*1
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
Stop in a Safe Place See Owner's Manual ·
Stop in a Safe Place within 0.3 miles*A ·
Stop in a Safe Place within 0.5 km (0.3 miles)*A ·
Stop in a Safe Place within 0.6 miles*A ·
Stop in a Safe Place within 1.0 km (0.6 miles)*A ·
Stop in a Safe Place within 0.9 miles*A ·
Stop in a Safe Place within 1.5 km (0.9 miles)*A ·
Stop in a Safe Place within 1.2 miles*A ·
Stop in a Safe Place within 2.0 km (1.2 miles)*A ·
Stop in a Safe Place within 3.1 miles*A ·
Stop in a Safe Place within 5.0 km (3.1 miles)*A ·
Stop in a Safe Place within 6.2 miles*A ·
Stop in a Safe Place within 10 km (6.2 miles)*A ·
Output Power Reduced Avoid Shifting to N ·
Avoid Shifting to N Visit Your Dealer ·
Hybrid System Stopped Stop in a Safe Place ·
Shift to P See Owner's Manual |
Sounds |
| Engine Stopped*1
·
Visit Your Dealer ·
Output Power Greatly Reduced Visit Your Dealer ·
Output Power Reduced Visit Your Dealer ·
Stop in a Safe Place See Owner's Manual ·
Stop in a Safe Place within 0.3 miles*A ·
Stop in a Safe Place within 0.5 km (0.3 miles)*A ·
Stop in a Safe Place within 0.6 miles*A ·
Stop in a Safe Place within 1.0 km (0.6 miles)*A ·
Stop in a Safe Place within 0.9 miles*A ·
Stop in a Safe Place within 1.5 km (0.9 miles)*A ·
Stop in a Safe Place within 1.2 miles*A ·
Stop in a Safe Place within 2.0 km (1.2 miles)*A ·
Stop in a Safe Place within 3.1 miles*A ·
Stop in a Safe Place within 5.0 km (3.1 miles)*A ·
Stop in a Safe Place within 6.2 miles*A ·
Stop in a Safe Place within 10 km (6.2 miles)*A ·
Output Power Reduced Avoid Shifting to N ·
Avoid Shifting to N Visit Your Dealer ·
Hybrid System Stopped Stop in a Safe Place ·
Shift to P See Owner's Manual |
Sounds |
| Traction Battery Needs to be Protected Refrain from the Use of N Position | Sounds |
| Release Accelerator
(and image display) |
Sounds |
| Drive-Start Control Malfunction Visit Your Dealer
(and image display) |
Sounds |
| Reverse Speed Control Activated | Sounds |
| Brake Override Malfunction Visit Your Dealer
(and image display) |
Sounds |
| Hybrid System Overheated Output Power Reduced
(and image display)*A |
Sounds |
| Accelerator and Brake Pedals Pressed Simultaneously
(and image display) |
- |
| Maintenance Required for Traction Battery Cooling Parts See Owner's Manual*A
Hybrid Battery Cooling Warning Visit Your Dealer*A |
- |
| Maintenance Required for Traction Battery Cooling Parts See Owner's Manual*A
Hybrid Battery Cooling Warning Visit Your Dealer*A |
Sounds |
| Low Auxiliary Battery See Owner's Manual | - |
| EV Mode Unavailable | Sounds |
| EV Mode Unavailable System Warming Up | Sounds |
| EV Mode Unavailable Hybrid Battery Low | Sounds |
| EV Mode Unavailable Speed Range Exceeded | Sounds |
| EV Mode Unavailable Reduce Acceleration to Activate | Sounds |
| EV Mode Deactivated | Sounds |
| EV Mode Deactivated Hybrid Battery Low | Sounds |
| EV Mode Deactivated Speed Range Exceeded | Sounds |
| EV Mode Deactivated Accelerator Pressed Too Far*A
EV Mode Deactivated Reduce Acceleration to Activate*A |
Sounds |
| Accelerator Pedal is Pressed | - |
| Have Traction Battery Inspected | - |
| Diagnosing Hybrid Battery | - |
| Vehicle Start Will Soon be Disabled Have Traction Battery Inspected | Sounds |
| Vehicle Start Disabled Until Traction Battery Inspected | - |
*A: Displayed message may vary depending on specifications.
The combination meter assembly displays the following messages based on signals received from the ECM and engine oil level sensor.
| Message | Buzzer |
|---|---|
| Check Engine Visit Your Dealer | Sounds |
| Reduced Engine Power Visit Your Dealer | Sounds |
| Engine Maintenance Required Visit Your Dealer | Sounds |
| Engine Coolant Temp High Stop in a Safe Place See Owner's Manual
(and image display) |
Sounds |
| Oil Pressure Low Stop in a Safe Place See Owner's Manual
(and image display) |
Sounds |
| Engine Oil Level Low Add or Replace | - |
| Fuel Low | - |
The combination meter assembly displays the following messages based on signals received from the ECM and engine oil level sensor.
| Message | Buzzer |
|---|---|
| Release Accelerator
(and image display) |
Sounds |
| Check Engine Visit Your Dealer | Sounds |
| Check Engine Reduced Engine Power Visit Your Dealer | Sounds |
| Engine Maintenance Required Visit Your Dealer | Sounds |
| Engine Coolant Temp High Stop in a Safe Place See Owner's Manual
(and image display) |
Sounds |
| Oil Pressure Low Stop in a Safe Place See Owner's Manual
(and image display) |
Sounds |
| Drive-Start Control Malfunction Visit Your Dealer
(and image display) |
Sounds |
| Reverse Speed Control Activated | Sounds |
| Brake Override Malfunction Visit Your Dealer
(and image display) |
Sounds |
| Engine Oil Level Low Add or Replace | - |
| Accelerator and Brake Pedals Pressed Simultaneously
(and image display) |
- |
| Fuel Low | - |
The combination meter assembly displays the following messages based on signals received from the hybrid vehicle control ECU*1 or ECM*2.
*1: HV Models
*2: Gasoline Models
| Message | Buzzer |
|---|---|
| Speed Limiter Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the hybrid vehicle control ECU*1 or ECM*2.
*1: HV Models
*2: Gasoline Models
| Message | Buzzer |
|---|---|
|
*: Models with full-speed range following function without brake hold |
|
| Press Brake* | Sounds |
| Radar Cruise Control Unavailable Clean Sensor | Sounds |
| Radar Cruise Control Unavailable | Sounds |
| Cruise Control Malfunction Visit Your Dealer | Sounds |
| Radar Cruise Active Please Pay Attention to Other Vehicles | - |
| Dynamic radar cruise control system status
(image display) |
- |
The combination meter assembly displays the following messages based on signals received from the forward recognition camera.
| Message | Buzzer |
|---|---|
| ADJUSTING FORWARD CAMERA | - |
| LTA Hold Steering Wheel
(and image display) |
- |
| LTA Steering Assist Unavailable Hold Steering Wheel
(and image display) |
- |
| LTA Hold Steering Wheel
(and image display) |
Sounds |
| LTA Malfunction Visit Your Dealer | Sounds |
| LTA Unavailable | Sounds |
| LTA Unavailable Below Approx. 50km/h | - |
| LTA Unavailable at Current Speed | - |
| Lane tracing assist system status
(image display) |
- |
| LTA Unavailable Below Approx. 32 MPH. | - |
| LTA Steering Assist Active Lane Centering Active | - |
| LTA Steering Assist Active | - |
The combination meter assembly displays the following messages based on signals received from the forward recognition camera.
| Message | Buzzer |
|---|---|
| RSA Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the transmission control ECU.
| Message | Buzzer |
|---|---|
| Transmission Oil Temp. High Stop in a Safe Place and See Owner's Manual | Sounds |
The combination meter assembly displays the following messages based on signals received from the ECM.
| Message | Buzzer |
|---|---|
| Press the Accelerator Pedal when Starting Off | - |
The combination meter assembly displays the following messages based on signals received from the AWD ECU assembly.
| Message | Buzzer |
|---|---|
| AWD TEST MODE | - |
| AWD System Malfunction 2WD Mode Engaged Visit Your Dealer | Sounds |
| AWD System Overheated 2WD Mode Engaged | Sounds |
| AWD System Overheated Switching to 2WD Mode | Sounds |
The combination meter assembly displays the following messages based on signals received from the tire pressure warning ECU and receiver.
| Message | Buzzer |
|---|---|
| TPWS Malfunction Visit Your Dealer | Sounds |
| Setting Tire Pressure Warning System*A
Setting TPWS*A |
- |
| Tire Pressure Recalibrating Please Wait until Complete*A
Registering Each TPWS Sensor*A |
- |
| Tire Pressure Low Check Tire
(and image display) |
- |
*A: Displayed message may vary depending on specifications.
The combination meter assembly displays the following messages based on signals received from the skid control ECU.
| Message | Buzzer |
|---|---|
|
*: HV Models |
|
| Braking Power Low Stop in a Safe Place See Owner's Manual | Sounds |
| Antilock Brake System Malfunction Visit Your Dealer | Sounds |
| Braking Power Low Visit Your Dealer* | Sounds |
| Low Braking Power Stop in a Safe Place See Owner's Manual* | Sounds |
| Traction Control Turned OFF | - |
| Secondary Collision Brake System Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the brake actuator assembly (skid control ECU).
| Message | Buzzer |
|---|---|
| EPB Shift Interlock Function Activated | Sounds |
| EPB Shift Interlock Function Deactivated | Sounds |
| EPB Automatically Applied | Sounds |
| Parking Brake Unavailable | Sounds |
| Parking Brake Temporarily Unavailable | Sounds |
| Parking Brake Unavailable Vehicle may Roll Park on Flat Road | Sounds |
| Parking Brake Unable to Disengage Press Brake and Push Parking Brake Switch to Release | Sounds |
| Parking Brake Unable to Disengage Close Door and Fasten Seat Belt | Sounds |
| Parking Brake ON | - |
| EPB Activation Stopped Incompletely | Sounds |
| Parking Brake Malfunction Visit Your Dealer | Sounds |
| Vehicle may Roll Shift to P | Sounds |
The combination meter assembly displays the following messages based on signals received from the power steering ECU.
| Message | Buzzer |
|---|---|
|
*1: HV Models *2: Gasoline Models |
|
| Power Steering Malfunction Steering Power Low Visit Your Dealer | Sounds |
| Voltage Abnormality Steering Power Low Visit Your Dealer | Sounds |
| Steering Power Low Visit Your Dealer | Sounds |
| Power Steering Malfunction Visit Your Dealer | Sounds |
| Hybrid System Stopped Steering Power Low*1 | Sounds |
| Engine Stopped Steering Power Low*2 | Sounds |
The combination meter assembly displays the following messages based on signals received from the parking assist ECU assembly.
| Message | Buzzer |
|---|---|
| WRITE ZERO-POINT OF STEERING ANGLE | - |
| END OF ADJUSTMENT | - |
| MEMORY ERROR | - |
| Switch to Brake
(and image display) |
Sounds |
| Press Brake Pedal
(and image display) |
Sounds |
| Brake! | Sounds |
| Object Detected Acceleration Reduced | Sounds |
| PKSB Malfunction Visit Your Dealer | Sounds |
| PKSB Unavailable | - |
| Parking Support Brake Unavailable Remove the Dirt of Rear Camera | - |
The combination meter assembly displays the following messages based on signals received from the blind spot monitor sensor RH.
| Message | Buzzer |
|---|---|
| Blind Spot Monitor Unavailable | Sounds |
| Blind Spot Monitor Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the main body ECU and certification ECU.
| Message | Buzzer |
|---|---|
| Push and Hold Power Switch for Emergency Stop | Sounds |
| Shift to N and Push POWER Switch to Restart | Sounds |
| Hybrid System Stopped Shift into P | Sounds |
| Hybrid System Stopped Stop in a Safe Place | Sounds |
| Shift to P when Parked | Sounds |
| Auto Power OFF to Conserve Battery | - |
| Key Not Detected Check Key Location | Sounds |
| Smart Entry & Start System Malfunction See Owner's Manual | Sounds |
| Turn Power OFF | Sounds |
| Key Detected in Vehicle | - |
| Press Brake Pedal and Touch Power Switch with Key | Sounds |
| Not Ready to Drive Press Brake Pedal and Push Power Switch to Start | - |
| Press Brake Pedal and Push Power Switch to Start | Sounds |
| Push Power Switch while Turning Steering Wheel in Either Direction | Sounds |
| Shift to P to Start | - |
| Key Battery Low Replace Key Battery | Sounds |
| A New Key has been Registered Contact Your Dealer for Details | - |
| Press Brake Pedal and Push Power Switch to Start
(and image display) |
- |
The combination meter assembly displays the following messages based on signals received from the main body ECU and certification ECU.
| Message | Buzzer |
|---|---|
|
*1: Models with CVT *2: Models with manual transaxle |
|
| Push and Hold Engine Switch for Emergency Stop | Sounds |
| Shift to N and Push ENGINE Switch to Restart*1 | Sounds |
| Press Clutch Pedal and Push Engine Switch to Restart*2 | Sounds |
| Engine Stopped Shift into P Position*1 | Sounds |
| Engine Stopped Stop in a Safe Place | Sounds |
| Shift to P when Parked*1 | Sounds |
| Auto Power OFF to Conserve Battery | - |
| Key Not Detected Check Key Location | Sounds |
| Smart Entry & Start System Malfunction See Owner's Manual | Sounds |
| Turn Power OFF | Sounds |
| Key Detected in Vehicle | - |
| Press Brake Pedal and Touch Engine Switch with Key*1 | Sounds |
| Press Clutch Pedal and Touch Engine Switch with Key*2 | Sounds |
| Not Ready to Drive Press Brake Pedal and Push Engine Switch to Start*1 | - |
| Not Ready to Drive*2 | - |
| Press Brake Pedal and Push Engine Switch to Start*1 | Sounds |
| Press Clutch Pedal and Push Engine Switch to Start*2
(and image display) |
Sounds |
| Push Engine Switch while Turning Steering Wheel in Either Direction | Sounds |
| Key Battery Low Replace Key Battery | Sounds |
| A New Key has been Registered Contact Your Dealer for Details | - |
| Press Brake Pedal and Push Engine Switch to Start*1
(and image display) |
- |
| Press Clutch Pedal and Push Engine Switch to Start*2
(and image display) |
- |
The combination meter assembly displays the following messages based on signals received from the airbag ECU assembly.
| Message | Buzzer |
|---|---|
| SRS Airbag System Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the millimeter wave radar sensor assembly.
| Message | Buzzer |
|---|---|
| CHECKING PCS BRAKE | - |
| BRAKE! | Sounds |
| Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature | - |
| Front Camera Low Visibility Unavailable See Owner's Manual | - |
| Front Camera Unavailable See Owner's Manual | - |
| Pre-Collision System Malfunction Visit Your Dealer | Sounds |
| VSC Turned OFF Pre-Collision Brake System Unavailable | - |
| Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual | - |
| Pre-Collision System Unavailable See Owner's Manual | - |
| Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor | - |
| Pre-Collision System OFF | - |
| Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual | - |
The combination meter assembly displays the following messages based on signals received from the main body ECU.
| Message | Buzzer |
|---|---|
| Window Open | Sounds |
The combination meter assembly displays the following messages based on signals received from the main body ECU.
| Message | Buzzer |
|---|---|
|
*1: If the vehicle has reached a speed of 5 km/h (3 mph). *2: 5 door models |
|
| Driver door open
(image display) |
- |
| Front passenger door open
(image display) |
|
| Rear passenger door LH open*2
(image display) |
|
| Rear passenger door RH open*2
(image display) |
|
| Hood open
(image display) |
|
| Back door open
(image display) |
|
| Driver door open while driving*1
(image display) |
Sounds |
| Front passenger door open while driving*1
(image display) |
|
| Rear passenger door LH open while driving*1, *2
(image display) |
|
| Rear passenger door RH open while driving*1, *2
(image display) |
|
| Hood open while driving*1
(image display) |
|
| Back door open while driving*1
(image display) |
|
The combination meter assembly displays the following messages based on signals received from the headlight ECU sub-assembly RH and headlight ECU sub-assembly LH or main body ECU.
| Message | Buzzer |
|---|---|
| Headlight System Uninitialized Visit Your Dealer | - |
| Front Camera Unavailable | - |
| Front Camera Vision Blocked Clean and Demist Windshield | - |
| Turn Lights OFF | Sounds |
| Headlight System Malfunction Visit Your Dealer | Sounds |
| To Activate Automatic High Beam, Switch Headlights to High Beam | - |
The combination meter assembly displays the following messages based on signals received from the vehicle approaching speaker controller.
| Message | Buzzer |
|---|---|
| Acoustic Vehicle Alerting System Malfunction Visit your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals.
| Message | Buzzer |
|---|---|
|
*: Models with manual transaxle |
|
| Roads may be Icy Drive with Care
(and image display) |
Sounds |
| Engine Oil Level Low Add or Replace | Sounds |
| Press the accelerator pedal when starting off | - |
| Check fuel cap | Sounds |
| Low Auxiliary Battery See Owner's Manual
(and image display) |
- |
| Low Battery Turn Power OFF | Sounds |
| iMT system malfunction Visit your dealer* | Sounds |
The reminder service/operation advisory function displays the following setting change reminders and operation support displays via an interrupt display when conditions are met according to the vehicle condition and various switch operations.
| Reminder Details | Display Condition | Multi-information Display | Choice |
|---|---|---|---|
| Headlight illumination reminder | When system determines vehicle is being driven at night with headlights turned off | Turn ON Headlamps | - |
| Turn headlights off after stopping reminder (when light control switch is set to HEAD) | When headlights are illuminated after ignition switch is turned off (light control switch is in HEAD position) | Headlamps Are ON | - |
| Turn headlights off after stopping reminder (when light control switch is set to AUTO) | When headlights are illuminated after ignition switch is turned off (light control switch is in AUTO position) | Headlamps Are ON
Turn Headlamps OFF? |
·
Yes ·
No |
| Rear seat reminder | When IG is turned OFF after the rear door is opened then closed during IG ON or before IG ON | Attention:
Check Rear Seat |
- |
| Close door windows during wiper operation reminder | If any door window is open when attempting to operate wipers | Close Open Windows? | ·
Yes ·
No |
Buzzer
The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.
|
*1: HV models *2: Gasoline models *3: Models with entry and start system *4: Models without entry and start system *5: Except models with manual transaxle *6: Models with tire pressure warning system *7: Models with electric parking brake system *8: Models with pre-collision system *9: Models with lane tracing assist system *10: Models with road sign assist system *11: Models with speed limiter system *12: Models with full-speed range following function without brake hold |
|
| Priority | Item |
| 1 | READY*1 |
| 2 | Pre-collision System Warning*8 |
| 3 | Hybrid System Start while Driving Notice Buzzer*1 |
| 4 | Push Power Switch*1/Engine Switch*2 Operation while Driving Warning*3 |
| 5 | Key Reminder*4 |
| 6 | Vehicle Proximity Warning |
| 7 | Pedestrian Warning |
| 8 | Lane Tracing Assist System Cancel Warning*9 |
| 9 | Lane Tracing Assist System Warning*9 |
| 10 | Hands off Steering Wheel Warning*9 |
| 11 | Unexpected Vehicle Motion Warning (Level 1) |
| 12 | Unexpected Vehicle Motion Warning (Level 2) |
| 13 | Brake Fluid Low Warning*2 |
| 14 | Brake Pedal Operation Request |
| 15 | Engine Oil Pressure Warning |
| 16 | Seat Belt Warning (Once) |
| 17 | Seat Belt Warning (Level 2) |
| 18 | Seat Belt Warning (Level 1) |
| 19 | EPS Warning (Once) |
| 20 | EPS Warning (Intermittent) |
| 21 | Accelerator Depression in N Position*1 |
| 22 | Hybrid System Warning (Intermittent: Pattern 1)*1 |
| 23 | Hybrid System Warning (Intermittent: Pattern 2)*1 |
| 24 | Hybrid System Warning (Intermittent: Pattern 3)*1 |
| 25 | Hybrid System Warning (Intermittent: Pattern 4)*1 |
| 26 | Hybrid System Warning (Continuous)*1 |
| 27 | Hybrid System Warning (Once)*1 |
| 28 | Auxiliary Power Source System Warning |
| 29 | Towing Prohibition Notification*1 |
| 30 | Road Sign Assist Indication*10 |
| 31 | Engine Coolant Temperature Warning |
| 32 | Door Open when Shift Position not P Warning*3 |
| 33 | Entry and Start System Warning (Intermittent 1)*3 |
| 34 | Shift P Request when Start Warning*5 |
| 35 | Rear Seat Reminder System Warning |
| 36 | Brake Pedal Operation Request*12 |
| 37 | Entry and Start System Warning (Intermittent 2)*3 |
| 38 | Entry and Start System Warning (Once)*3 |
| 39 | Multi-information Display Warning |
| 40 | Check Engine Warning |
| 41 | Accelerator Hold Warning*1 |
| 42 | Hybrid Battery Check Request Notification |
| 43 | Hybrid Battery Low Warning (Continuous)*1 |
| 44 | Hybrid Battery Low Warning (Intermittent)*1 |
| 45 | Brake System Learning |
| 46 | Start Brake System Check |
| 47 | End Brake System Check |
| 48 | Brake System Malfunction |
| 49 | Unfunctional Brake System (Pattern 1) |
| 50 | Unfunctional Brake System (Pattern 2) |
| 51 | Hybrid Unit Overheat Warning*1 |
| 52 | Electric Parking Brake System Cancel Warning 1*7 |
| 53 | Electric Parking Brake System Cancel Warning 2*7 |
| 54 | Brake Hold System Control Not Release Warning*7 |
| 55 | Dynamic Radar Cruise Control Cancel Warning |
| 56 | Low Speed Zone Leading Vehicle Lost Warning*8 |
| 57 | Immobiliser Certification Reminder*3 |
| 58 | Speed Limiter*11 |
| 59 | Speed Limit Exceed Warning |
| 60 | Parking Brake Engaged Warning |
| 61 | Door Open while Driving Warning |
| 62 | Vehicle Sway Warning*9 |
| 63 | Shift Reject Warning*5 |
| 64 | Traction Battery Cooling Performance Down Notification*1 |
| 65 | Tire Pressure Warning*6 |
| 66 | EV Drive Mode Reject Warning*1 |
| 67 | Light Reminder |
| 68 | Brake System Application Driven (Twice) |
| 69 | Brake System Application Driven (Pattern 1) |
| 70 | Brake System Application Driven (Pattern 2) |
| 71 | Electrical Ignition Switch System Control |
| 72 | Pre-collision Brake Assist Notification Buzzer*8 |
| 73 | Pre-collision Warning Buzzer*8 |
| 74 | Brake Inspections Standby Mode Notification Buzzer*8 |
| 75 | Radar Axis Adjustment Complete Notification Buzzer*8 |
| 76 | Camera Axis Adjustment Complete Notification Buzzer*8 |
| 77 | Pre-collision Braking Notification Buzzer*8
Return from Brake Inspection Mode Notification Buzzer*8 Radar Axis Adjustment Incomplete Notification Buzzer*8 Camera Axis Adjustment Start Notification Buzzer*8 |
| 78 | Turn Signal/Hazard Warning Operation |
Rear Seat Belt Warning
The rear seat belt warning function indicates the state of the rear seat belts.
The combination meter assembly receives a rear seat belt warning signal based on the rear seat belt buckle switches and courtesy switches for the rear doors, occupant detection sensor (for rear seat). When the signal is received, combination meter assembly operates the lights. If a warning is necessary, the buzzer in the combination meter assembly will also sound.
The flow of operations that results in a rear seat belt warning is as follows:
| Step | Condition Transition | Rear Seat Belt Warning Indicator | Buzzer |
|---|---|---|---|
|
*1: Sound cycle is 1.2 seconds. *2: Sound cycle is 0.4 seconds. *3: Except models with manual transaxle |
|||
| (a) | The ignition switch is turned off. | Rear seat belt warning indicator is not illuminated. | No Sound |
| (b) | Any of the rear seat belts are unfastened. | Seats with an unfastened seat belt will be illuminated or blinked regardless of the number of occupants. | If the vehicle speed exceeds 20 km/h (approximately 12 mph):
1.
Sounds once*1 2.
Sounds for an additional 24 seconds*1 3.
Sounds for an additional 100 seconds*2 |
| (c) | When one of the following conditions is met, the buzzer will stop sounding.
- The seat belt is refastened. - The vehicle speed decreases to less than approximately 2 km/h (approximately 1.2 mph) and either the parking brake is applied or the shift position is P*3. |
·
Seats with an unfastened seat belt will be blinked regardless of the number of occupants. ·
The warning will be blinked and then illuminated. |
Stops sounding |