Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM › 2020.03–2020.07
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0417607 REAR AXLE BEAM A

REAR SUSPENSION  REAR AXLE BEAM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front axle hub sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

for HV Model
·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 42450B 1.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42450A 2.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48231B 3.REMOVE REAR COIL SPRING LH

Hide 48231A 4.REMOVE AND INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 42110F 5.REMOVE REAR AXLE BEAM ASSEMBLY

a.

Support the rear axle beam assembly using an engine lifter, 2 wooden blocks and 2 plate lift attachments or equivalent tools.

C433947C01
1.615,2.458 1.615,2.042 true 2.229,1.938 1.885,1.688 true 5.354,1.708 5.042,1.948 true 4.333,1.729 4.094,1.958 true 3.125,1.938 2.885,1.729 true 1.531,2.458 1.844,2.615 0.313,0.156 10 false *a 2.271,1.865 2.583,2.021 0.313,0.156 10 false *b 3.188,1.865 3.5,2.021 0.313,0.156 10 false *c 4.833,1.875 5.146,2.031 0.313,0.156 10 false *b 3.885,1.865 4.198,2.021 0.313,0.156 10 false *c
*a Engine Lifter *b Wooden Block
*c Plate Lift Attachment - -


CAUTION:

Make sure to secure the rear axle beam assembly to prevent it from dropping.



b.

Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

NOTICE:

Because the nuts have their own stoppers, do not turn the nuts. Loosen the bolts with the nuts secured.



c.

Remove the 2 bolts and rear axle beam assembly from the vehicle.

C429098C03
5.771,1.719 6.271,1.688 true 1.292,1.677 0.771,1.719 true 2.969,1.583 3.583,1.281 3.583,1.281 4.167,1.573 true 2.958,3.125 3.625,2.198 true 0.521,1.646 0.76,1.875 0.24,0.229 10 true *b 3.521,1.073 3.771,1.25 0.25,0.177 10 true *a 2.781,3.063 3.094,3.219 0.313,0.156 10 false *c 6.323,1.604 6.542,1.823 0.219,0.219 10 true *b
*a Plate Lift Attachment *b Wooden Block
*c Wooden Block - -