Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2020.03–2020.07
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0417612 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front shock absorber assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 48810 2.SEPARATE FRONT STABILIZER LINK ASSEMBLY

a.
C431442

Remove the nut to separate the front stabilizer link assembly from the front shock absorber with coil spring.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 89543 3.SEPARATE FRONT SPEED SENSOR

a.
C431859

Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



Hide 48684B 4.REMOVE FRONT SUSPENSION SUPPORT DUST COVER

a.
C435738

Remove the front suspension support dust cover from the front shock absorber with coil spring.


Hide 5.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C435934C01
0.792,1.865 1.167,1.75 false 1.052,2.104 1.438,1.958 false 0.625,1.802 0.938,1.958 0.313,0.156 10 false *a 0.885,2.052 1.198,2.208 0.313,0.156 10 false *b
*a Wooden Block
*b Jack
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.

NOTICE:

Keep the front lower No. 1 suspension arm sub-assembly supported until installation of the front shock absorber with coil spring is complete.



b.
C431861

Remove the 2 bolts and 2 nuts, to separate the front shock absorber with coil spring from the steering knuckle.

NOTICE:
·

When removing the nuts, keep the bolts from rotating.

·

Use wire or an equivalent tool to hang the separated steering knuckle.




c.
C429632N01
1.115,0.656 1.771,0.875 true 2.302,0.688 2.573,0.521 true 0.646,0.552 1.104,0.75 0.458,0.198 10 true SST 2.583,0.427 3.042,0.625 0.458,0.198 10 true SST

Using SST, fix the front shock absorber rod and remove the nut.

SST
09729-00170  
09729-38060  


d.

Remove the front No. 2 suspension support.


e.

Remove the front shock absorber with coil spring from the vehicle.


Hide 48609E 6.REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C287918E08
2.333,1.26 2.677,0.969 false 2.719,0.906 3.177,1.104 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-30022  (09727-00010, 09727-00022, 09727-00031)


b.

Attach the hooks of each SST arm across the diameter of the front coil spring.

CAUTION:
·
C322989C01
1.563,0.698 1.833,1.219 1.833,1.219 2.135,0.771 false 1.771,1.271 2.083,1.469 0.313,0.198 10 false *a
*a Front Coil Spring Diameter


Do not perform the work without checking to make sure that the claws of the hooks are securely engaged.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.

·
C331810

Do not install SST to the front coil spring unless its top and bottom hook distance is set to the widest condition.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.

·
C340569

Do not install SST when the distances between the SST arms or the number of coils of the coil spring between the hooks are not the same.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.




c.

Install the stopper pins to the hooks of SST.

CAUTION:
·
C322990

Do not perform the work if the stopper pin is not securely installed.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.




d.

Using SST, compress the front coil spring.

CAUTION:
·
C332538

While compressing the spring, if the front coil spring starts to bend into a bow shape, do not continue the work.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.

·
C332540

Do not compress the springs so far that the coils of the springs touch each other.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.

·
C332542

Do not use an impact wrench.

·

The threads may be stripped, or the sudden compression may result in slack that causes the hooks to slip off, causing the spring to fly out and possibly resulting in injury.

·
C340570E01
0.938,3.125 1.521,3.125 true 0.646,3.052 1.104,3.25 0.458,0.198 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

·

If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.



SST
09727-00110  


e.
C454327N01
1.385,2.354 2.052,1.5 true 1.063,2.313 1.521,2.51 0.458,0.198 10 false SST

Check that the front coil spring has become free, and using SST and a 6 mm hexagon socket wrench, remove the front support to front shock absorber nut.

SST
09729-97202  

CAUTION:
·
C332546

If the front coil spring has not become free, do not remove the front support to front shock absorber nut.

·

The spring force will cause the components to be scattered, possibly resulting in injury.




Hide 48609 7.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.

Remove the front suspension support sub-assembly from the front shock absorber assembly.


Hide 48619A 8.REMOVE STRUT MOUNTING BEARING

a.

Remove the strut mounting bearing from the front upper coil spring seat.


Hide 48471C 9.REMOVE FRONT UPPER COIL SPRING SEAT

a.

Remove the front upper coil spring seat from the front shock absorber assembly.


Hide 48559B 10.REMOVE FRONT NO. 1 SHOCK ABSORBER DUST COVER

C428576C01
1.615,1.365 1.688,1.771 1.688,1.771 2.24,1.396 false 1.042,1.281 1.292,1.281 false 0.844,1.198 1.156,1.354 0.313,0.156 10 false *1 1.615,1.781 1.927,1.938 0.313,0.156 10 false *a
*1 Front No. 1 Shock Absorber Dust Cover
*a Claw


a.

Disengage the end of the front No. 1 shock absorber dust cover from the claws of the front shock absorber assembly.


b.

Remove the front No. 1 shock absorber dust cover with front upper coil spring insulator from the front shock absorber assembly.


Hide 48157C 11.REMOVE FRONT UPPER COIL SPRING INSULATOR

a.

Remove the front upper coil spring insulator from the front No. 1 shock absorber dust cover.


Hide 48132 12.REMOVE FRONT COIL SPRING

a.

Remove the front coil spring and SST.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 48331C 13.REMOVE FRONT SPRING BUMPER

a.

Remove the front spring bumper from the front shock absorber assembly.


Hide 48158C 14.REMOVE FRONT LOWER COIL SPRING INSULATOR

a.

Remove the front lower coil spring insulator from the front shock absorber assembly.


Hide 48510 15.REMOVE FRONT SHOCK ABSORBER ASSEMBLY