Refer to DTC P019511.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P019511
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P019515 | Engine Oil Temperature Sensor Circuit Short to Battery or Open | The engine oil temperature sensor (engine oil pressure and temperature sensor) output voltage is higher than 4.865 V for 5 seconds or more (1 trip detection logic). | ·
Open or short in engine oil temperature sensor (engine oil pressure and temperature sensor) circuit ·
Engine oil temperature sensor (engine oil pressure and temperature sensor) ·
ECM |
- | DTC stored | SAE: P0198 |
When a DTC is output, check the Data List item "Engine Oil Temperature Sensor" using the GTS.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
| DTC No. | Engine Oil Temperature Sensor | Malfunction |
|---|---|---|
| P019515 | Higher than 150°C (302°F) | ·
Short to +B in THEO circuit ·
Open in THEO circuit ·
Open in EPEO circuit |
If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
The ECM monitors the engine oil temperature sensor (engine oil pressure and temperature sensor) and uses the sensor voltage to calculate the engine oil temperature. If the engine oil temperature sensor (engine oil pressure and temperature sensor) output voltage deviates from the normal operating range, the ECM determines that the engine oil temperature sensor (engine oil pressure and temperature sensor) circuit is malfunctioning and stores this DTC.
Example:
If the engine oil temperature sensor (engine oil pressure and temperature sensor) output voltage is higher than 4.865 V for 5 seconds or more, the ECM will store this DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 10 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P019515.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
Refer to DTC P019511.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P019511
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Pre-procedure1
Disconnect the engine oil temperature sensor (engine oil pressure and temperature sensor) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| D32-3 (VC) - D32-2 (GND) | Ignition switch ON | 4.5 to 5.5 V |
| D32-4 (TOUT) - D32-2 (GND) | Ignition switch ON | 3.0 to 5.5 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| D32-2 (GND) - Body ground | Ignition switch off | Below 1 Ω |
| D32-3 (VC) - D32-4 (TOUT) | Ignition switch off | 171 to 189 kΩ |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the engine oil temperature sensor (engine oil pressure and temperature sensor) connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D32-2 (GND) - D51-100 (EPEO) | Always | Below 1 Ω |
| D32-4 (TOUT) - D51-123 (THEO) | Always | Below 1 Ω |
| D32-4 (TOUT) or D51-123 (THEO) - Other terminals | Always | 10 kΩ or higher |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG