Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM J

M15A-FXE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, auxiliary battery voltage is applied to IGP of the ECM. When the transistor in the MREL circuit operates, current flows from the auxiliary battery to ground through the drive circuit of the EFI-MAIN NO. 1 relay, thus operating the relay which supplies power to the +B and +B2 terminals of the ECM.

WIRING DIAGRAM

A457722E01
0.552,4.813 1.688,5.125 1.135,0.313 10 false Auxiliary Battery 0.406,4 1.323,4.198 0.917,0.198 10 false BATT-MAIN 1.01,2.135 1.927,2.333 0.917,0.198 10 false IGP-MAIN 0.74,0.625 1.656,0.823 0.917,0.198 10 false AM1 5.781,3.625 6.698,3.823 0.917,0.198 10 false MREL 5.844,2.865 6.76,3.063 0.917,0.198 10 false +B 5.844,3.292 6.76,3.49 0.917,0.198 10 false +B2 5.844,1.865 6.76,2.063 0.917,0.198 10 false IGP 6.146,4.854 6.854,5.323 0.708,0.469 10 false ECM 6.167,4.656 6.594,4.844 0.427,0.188 10 false A53 4.958,2.552 5.583,2.802 0.625,0.25 10 false EFI NO. 2 4.938,2.292 5.177,2.5 0.24,0.208 10 false 1 5.292,2.302 5.531,2.51 0.24,0.208 10 false 2 4.646,2.135 5.563,2.333 0.917,0.198 10 false INJ 5.635,2.74 5.875,2.948 0.24,0.208 10 false 2 5.635,3.188 5.875,3.396 0.24,0.208 10 false 3 5.563,3.604 5.802,3.813 0.24,0.208 10 false 11 5.854,4.25 6.771,4.448 0.917,0.198 10 false E1 5.635,4.104 5.875,4.313 0.24,0.208 10 false 6 5.552,1.865 5.792,2.073 0.24,0.208 10 false 10 2.448,4.042 3.781,4.365 1.333,0.323 10 false EFI-MAIN NO. 1 3.271,3.625 3.51,3.833 0.24,0.208 10 false 1 3.271,3.198 3.51,3.406 0.24,0.208 10 false 3 2.438,3.625 2.677,3.833 0.24,0.208 10 false 2 2.438,3.208 2.677,3.417 0.24,0.208 10 false 5 0.813,3.458 2.146,3.781 1.333,0.323 10 false EFI-MAIN NO. 1 2.802,2.708 3.719,2.906 0.917,0.198 10 false IGP 3.25,2.271 3.49,2.479 0.24,0.208 10 false 1 2.458,2.281 2.698,2.49 0.24,0.208 10 false 2 3.25,1.865 3.49,2.073 0.24,0.208 10 false 5 2.458,1.875 2.698,2.083 0.24,0.208 10 false 3 0.406,1.302 0.99,1.875 0.583,0.573 10 false INP STD NO. 1-3 1.292,1.031 3.24,1.344 1.948,0.313 10 false Ignition Switch Assembly*2 1.323,0.844 2.24,1.042 0.917,0.198 10 false H54 1.51,0.365 1.75,0.573 0.24,0.208 10 false 7 2.729,0.354 2.969,0.563 0.24,0.208 10 false 8 3.063,0.615 3.302,0.823 0.24,0.208 10 false *2 3.802,0.625 4.042,0.833 0.24,0.208 10 false *1 5.292,0.979 6.208,1.177 0.917,0.198 10 false H45 5.583,0.979 7.115,1.531 1.531,0.552 10 false Certification ECU (Smart Key ECU Assembly)*1 5.823,0.479 6.74,0.677 0.917,0.198 10 false IGPD 5.49,0.365 5.729,0.573 0.24,0.208 10 false 24 2.021,4.927 5.021,5.188 3,0.26 10 false *1: w/ Entry and Start System 2.031,5.271 5.031,5.531 3,0.26 10 false *2: w/o Entry and Start System 1.208,0.594 1.448,0.802 0.24,0.208 10 false *2 2.396,0.354 2.635,0.563 0.24,0.208 10 false IG1 1.708,0.354 2.073,0.563 0.365,0.208 10 false AM1 6.375,3.729 6.927,3.896 0.552,0.167 10 false IC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A53 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A53-6 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IGP VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGP VOLTAGE)
a.

Disconnect the ECM connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A53-10 (IGP) - A53-6 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI-MAIN NO. 1 RELAY

NG

6.INSPECT IGP RELAY
3.INSPECT EFI-MAIN NO. 1 RELAY

OK

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE EFI-MAIN NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
a.

Remove the A/F HTR relay, VVT relay, EFI-MAIN NO. 1 relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay from the No. 1 engine room relay block.

HINT:

Remove the A/F HTR relay, VVT relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



b.

Disconnect the A53 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 1 relay) - A53-11 (MREL) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) - A53-2 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) - A53-3 (+B2) Always Below 1 Ω
1 (EFI-MAIN NO. 1 relay) or A53-11 (MREL) - Body ground and other terminals Always 10 kΩ or higher
3 (EFI-MAIN NO. 1 relay), A53-2 (+B) or A53-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
A459395C01
0.198,1.177 0.51,1.333 0.313,0.156 10 false *1 0.875,0.125 1.188,0.281 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI-MAIN NO. 1 Relay


a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V
2 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - EFI-MAIN NO. 1 RELAY)

6.INSPECT IGP RELAY

OK

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - ECM)

NG

REPLACE IGP RELAY

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - ECM)
a.

Remove the IGP relay from the No. 1 engine room relay block.


b.

Disconnect the A53 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - A53-10 (IGP) Always Below 1 Ω
5 (IGP relay) or A53-10 (IGP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGP RELAY)
A459393C01
0.229,1.135 0.542,1.333 0.313,0.198 10 false *1 1.01,0.135 1.323,0.333 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGP Relay


a.

Remove the IGP relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IGP relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - IGP RELAY)

9.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)
A459393C01
0.229,1.135 0.542,1.333 0.313,0.198 10 false *1 1.01,0.135 1.323,0.333 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGP Relay


a.

Remove the IGP relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGP relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IGP RELAY)

B

11.INSPECT IGNITION SWITCH ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IGP RELAY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Remove the IGP relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-24 (IGPD) - 1 (IGP relay) Always Below 1 Ω
H45-24 (IGPD) or 1 (IGP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGNITION SWITCH ASSEMBLY

OK

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IGP RELAY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IGP RELAY)
a.

Disconnect the H54 ignition switch assembly connector.


b.

Remove the IGP relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-8 (IG1) - 1 (IGP relay) Always Below 1 Ω
H54-8 (IG1) or 1 (IGP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR