Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM D

M15A-FXE ENGINE CONTROL  SFI SYSTEM  DTC CHECK / CLEAR  


NOTICE:

When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and Freeze Frame Data recorded in normal mode are cleared. Before changing modes, always check and make a note of DTCs and Freeze Frame Data.


HINT:
·

DTCs which are stored in the ECM can be displayed on the GTS. The GTS can display the confirmed and pending DTCs.

·

Some DTCs are not stored if the ECM does not detect the same malfunction again during a second consecutive driving cycle. However, such malfunctions, detected on only one occasion, are stored as pending DTCs.



CHECK DTC


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Check the DTC(s) and Freeze Frame Data, and then write them down.

HINT:
GTS Display Description
Test Failed Shows the malfunction judgment results during the current trip.
Pending Shows the malfunction judgment results up to now. (Indicates the possibility of a malfunction when no DTC is confirmed.)
Confirmed Shows the DTCs confirmed up to now. (The number of current trips differs for each DTC.)





CHECK TIME STAMP


HINT:

By checking Time Stamp, the time and order in which DTCs were stored in an ECU can be checked.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus Health Check.


e.

Perform the following steps when the data setting screen is displayed.


f.

Select the systems for which to perform Health Check and check for time stamp data.

Selectable items:
·

Powertrain

·

Chassis

·

Body

·

Store All Data



g.

Select "Yes" when "Do you want to store time stamp data?" is displayed.

HINT:

If "Yes" is not selected, time stamp data will not be stored.



h.

After Health Check has completed, select "Time Stamp Data" to display the Time Stamp screen.


i.

Select the desired system from the drop-down list on the bottom of the Time Stamp screen.


j.

Check the order and time which DTCs were stored for the selected system.



CLEAR DTC


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372


CLEAR DTC (Without using GTS)


a.

Perform either of the following operations:

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




i.

Disconnect the cable from the negative (-) auxiliary battery terminal for more than 1 minute.


ii.

Remove the EFI NO. 1 fuse from the No. 1 engine room relay block located inside the engine compartment for more than 1 minute.