Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM36W0E _59 Vehicle Exterior _087824 LIGHTING (EXT) _0419675 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Clearance Light/Daytime Running Light Circuit  


DESCRIPTION

Clearance light function:

When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the light control LED ECU and illuminates the clearance lights.

Daytime running light function:

When the operation conditions of the daytime running lights are met, the main body ECU (multiplex network body ECU) sends an illumination request signal to the light control LED ECU and illuminates the daytime running lights.


WIRING DIAGRAM

E438235E04
1.125,1.844 1.583,2.042 0.458,0.198 10 false A86 1.979,5.229 2.438,5.427 0.458,0.198 10 false A5 0.906,6.385 3.052,6.635 2.146,0.25 10 false : CXPI Communication Line 0.094,5.688 1.469,6.24 1.375,0.552 10 false Semiconductor Power Integration Computer 1.979,5.385 3.521,5.677 1.542,0.292 10 false Headlight Assembly RH 1.125,4.885 1.583,5.083 0.458,0.198 10 false A86 3.896,4.458 5.979,4.698 2.083,0.24 10 false Power Distribution Box Assembly 5.271,5.719 6.927,6.417 1.656,0.698 10 false Main Body ECU (Multiplex Network Body ECU) 1.198,1.656 1.656,1.854 0.458,0.198 10 false 1 1.208,4.698 1.667,4.896 0.458,0.198 10 false 2 0.906,4.885 1.365,5.083 0.458,0.198 10 false L 0.927,1.865 1.385,2.063 0.458,0.198 10 false L 1.885,4.823 2.344,5.021 0.458,0.198 10 false 2 1.885,1.729 2.344,1.927 0.458,0.198 10 false 2 1.875,1.948 2.073,2.156 0.198,0.208 10 false 1 1.885,4.521 2.344,4.719 0.458,0.198 10 false 1 3.396,1.75 3.854,1.948 0.458,0.198 10 false 5 3.375,4.792 3.833,4.99 0.458,0.198 10 false 5 2.073,4.906 2.531,5.104 0.458,0.198 10 false LO 2.063,4.667 2.521,4.865 0.458,0.198 10 false AS1 3.188,4.896 3.646,5.094 0.458,0.198 10 false E 3.188,1.833 3.646,2.031 0.458,0.198 10 false E 2.073,1.833 2.531,2.031 0.458,0.198 10 false LO 2.063,2.094 2.521,2.292 0.458,0.198 10 false AT1 2.01,2.635 2.469,2.833 0.458,0.198 10 false A4 2.01,2.802 3.552,3.167 1.542,0.365 10 false Headlight Assembly LH 6.052,3.396 6.51,3.594 0.458,0.198 10 false CXPI 0.688,3.406 1.146,3.604 0.458,0.198 10 false CXPI

HEADLIGHT ASSEMBLY CIRCUIT (for LED Type)


E440208E01
3.115,5.125 5.219,5.521 2.104,0.396 10 false Headlight Assembly 5.521,3.125 6.469,3.99 0.948,0.865 10 false Headlight Lens Sub-assembly 5.844,1.74 6.76,2.542 0.917,0.802 10 false Clearance Light / Daytime Running Light 3.906,3.135 4.875,3.531 0.969,0.396 10 false Wire Harness 4.958,1.438 5.115,1.635 0.156,0.198 10 false C 4.958,2.542 5.115,2.74 0.156,0.198 10 false C 3.677,1.438 3.833,1.635 0.156,0.198 10 false B 3.677,2.542 3.833,2.74 0.156,0.198 10 false B 1.531,1.51 2.625,1.708 1.094,0.198 10 false DC/DC Converter 1.885,2.396 3.417,2.594 1.531,0.198 10 false CPU 1.583,3.26 2.813,3.521 1.229,0.26 10 false CXPI Transceiver 1.479,3.958 2.708,4.177 1.229,0.219 10 false Light Control LED 0.844,1.438 1,1.635 0.156,0.198 10 false B 0.844,2.313 1,2.51 0.156,0.198 10 false B 0.854,3.24 1.01,3.438 0.156,0.198 10 false B 0.26,1.313 0.583,1.51 0.323,0.198 10 false LO 0.25,2.198 0.573,2.396 0.323,0.198 10 false E 0.229,2.927 0.688,3.573 0.458,0.646 10 false AT1*1, AS1*2 4.969,1.24 5.125,1.438 0.156,0.198 10 false 2 4.948,2.344 5.104,2.542 0.156,0.198 10 false 1 3.646,1.229 3.938,1.51 0.292,0.281 10 false 17 3.688,2.344 3.844,2.542 0.156,0.198 10 false 6 0.823,1.229 1.115,1.531 0.292,0.302 10 false 19 0.865,2.125 1.021,2.323 0.156,0.198 10 false 8 0.854,3.042 1.01,3.24 0.156,0.198 10 false 1 2.802,1.865 3.427,2.823 0.625,0.958 10 false Switching Circuit 5.646,5.813 7.125,6.219 1.479,0.406 10 false *1: for LH Side 5.667,6.219 7.146,6.625 1.479,0.406 10 false *2: for RH Side


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

*1: w/ Entry and Start System




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Daytime Running Light Daytime running lights OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Daytime Running Light
50004 449 53
OK:

Clearance lights and daytime running lights illuminate.



Result:
Result Proceed to
OK A
NG (LH side clearance light and daytime running light does not illuminate.) B
NG (RH side clearance light and daytime running light does not illuminate.) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT HEADLIGHT ASSEMBLY LH (LO TERMINAL VOLTAGE)

C

7.INSPECT HEADLIGHT ASSEMBLY RH (LO TERMINAL VOLTAGE)
2.INSPECT HEADLIGHT ASSEMBLY LH (LO TERMINAL VOLTAGE)
a.

Disconnect the A4 headlight unit assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-2 (LO) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LENS SUB-ASSEMBLY LH - LIGHT CONTROL LED ECU LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LENS SUB-ASSEMBLY LH - LIGHT CONTROL LED ECU LH)
E438263C04
5.188,0.813 5.552,1.042 0.365,0.229 3.313,0.156 3.677,0.385 0.365,0.229 1.208,0.094 1.573,0.323 0.365,0.229 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.313,0.135 1.625,0.333 0.313,0.198 10 false A4 3.458,0.198 3.771,0.396 0.313,0.198 10 false B 5.313,0.854 5.625,1.052 0.313,0.198 10 false C 2.406,0.125 2.719,0.323 0.313,0.198 10 false *b 4.885,0.146 5.198,0.344 0.313,0.198 10 false *c
*a Component without harness connected
(to Wire Harness)
*b Component without harness connected
(to Light Control LED ECU)
*c Component without harness connected
(to Headlight Lens Sub-assembly LH)
- -




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-[17] - C-[2] Always Below 1 Ω
B-[6] - C-[1] Always Below 1 Ω
A4-2 (LO) - B-[19] Always Below 1 Ω
A4-5 (E) - B-[8] Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK LIGHT CONTROL LED ECU LH

NG

5.CHECK LIGHT CONTROL LED ECU LH
a.

Interchange the light control LED ECU LH with RH and connect the connectors to them.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

6.CHECK OPERATION (DAYTIME RUNNING LIGHT)
6.CHECK OPERATION (DAYTIME RUNNING LIGHT)
a.

Check that the daytime running light operates normally.

OK:

Daytime running light operates normally.



Result:
Proceed to
OK
NG



OK

NG

7.INSPECT HEADLIGHT ASSEMBLY RH (LO TERMINAL VOLTAGE)
a.

Disconnect the A5 headlight assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A5-2 (LO) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HEADLIGHT LENS SUB-ASSEMBLY RH - LIGHT CONTROL LED ECU RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HEADLIGHT LENS SUB-ASSEMBLY RH - LIGHT CONTROL LED ECU RH)
E438263C05
5.188,0.813 5.552,1.042 0.365,0.229 3.313,0.156 3.677,0.385 0.365,0.229 1.208,0.094 1.573,0.323 0.365,0.229 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.313,0.135 1.625,0.333 0.313,0.198 10 false A5 3.458,0.198 3.771,0.396 0.313,0.198 10 false B 5.313,0.854 5.625,1.052 0.313,0.198 10 false C 2.406,0.125 2.719,0.323 0.313,0.198 10 false *b 4.885,0.146 5.198,0.344 0.313,0.198 10 false *c
*a Component without harness connected
(to Wire Harness)
*b Component without harness connected
(to Light Control LED ECU)
*c Component without harness connected
(to Headlight Lens Sub-assembly RH)
- -




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-[17] - C-[2] Always Below 1 Ω
B-[6] - C-[1] Always Below 1 Ω
A5-2 (LO) - B-[19] Always Below 1 Ω
A5-5 (E) - B-[8] Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK LIGHT CONTROL LED ECU RH

NG

10.CHECK LIGHT CONTROL LED ECU RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors to them.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

11.CHECK OPERATION (DAYTIME RUNNING LIGHT)
11.CHECK OPERATION (DAYTIME RUNNING LIGHT)
a.

Check that the daytime running light operates normally.

OK:

Daytime running light operates normally.



Result:
Proceed to
OK
NG



OK

NG