Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0419699 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P033531  Crankshaft Position Sensor "A" No Signal  


DESCRIPTION

The TCM receives the engine speed signal from the ECM via CAN communication and direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P033531 Crankshaft Position Sensor "A" No Signal When the engine speed signal received from the ECM via CAN communication is 500 rpm or more, the signal received via direct line is 0 rpm for 5 seconds or more (1-trip detection logic).
·

SFI system

·

ECM

·

TCM

·

Wire harness or connector

·

Certification ECU (Smart key ECU assembly) (w/ Entry and Start System)


Comes on DTC stored SAE Code:
P0335

MONITOR DESCRIPTION

The TCM detects malfunctions by comparing the engine speed signals received from the ECM via direct line and CAN communication.

If the TCM receives the engine speed signal via CAN communication but not via direct line, it will illuminate the MIL and store this DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P033531.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

w/o Entry and Start System:
B478908E40
1.125,1.583 2.51,1.865 1.385,0.281 10 false A54 1.115,1.76 1.667,2.052 0.552,0.292 10 false ECM 0.854,2.219 2.802,2.531 1.948,0.313 10 false : CAN Communication Line 1.51,0.75 2.063,1.042 0.552,0.292 10 false NEO 1.927,0.74 2.875,1.063 0.948,0.323 10 false 16 5.281,0.75 5.833,1.042 0.552,0.292 10 false 13 5.542,0.75 6.094,1.042 0.552,0.292 10 false NE 5.75,0.375 6.302,0.667 0.552,0.292 10 false +B 6.125,0.917 6.677,1.208 0.552,0.292 10 false IC 5.833,1.583 6.385,1.875 0.552,0.292 10 false D71 5.844,1.75 6.448,1.969 0.604,0.219 10 false TCM

w/ Entry and Start System:
C400413E08
0.854,4.25 4.521,4.448 3.667,0.198 10 false : CAN Communication Line 1.094,3.604 1.552,3.802 0.458,0.198 10 false A54 1.094,3.781 1.552,3.979 0.458,0.198 10 false ECM 1.531,2.781 1.99,2.979 0.458,0.198 10 false NEO 1.906,2.781 2.365,2.979 0.458,0.198 10 false 16 5.281,2.771 5.74,2.969 0.458,0.198 10 false 15 5.271,0.896 5.729,1.094 0.458,0.198 10 false 13 5.781,0.531 6.24,0.729 0.458,0.198 10 false +B 5.563,0.896 6.021,1.094 0.458,0.198 10 false NE 5.552,2.771 6.01,2.969 0.458,0.198 10 false NE 5.833,1.729 6.292,1.927 0.458,0.198 10 false D71 5.844,1.906 6.302,2.104 0.458,0.198 10 false TCM 5.781,2.396 6.24,2.594 0.458,0.198 10 false +B 5.24,3.615 6.427,3.823 1.188,0.208 10 false H45 5.24,3.792 6.781,4.469 1.542,0.677 10 false Certification ECU (Smart Key ECU Assembly) 6.125,1.167 6.438,1.365 0.313,0.198 10 false IC 6.125,3.031 6.438,3.229 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

Read freeze frame data using the GTS. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



DATA LIST


HINT:

The engine speed may be indicated as zero despite the engine running normally. This is caused by the NE signal not being received from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


a.

Start the engine.


b.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
750 to 850 rpm: Engine idling (shift lever in P, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Powertrain > Transmission > Data List
Tester Display
Engine Speed
50003 373 211


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/o Entry and Start System A
w/ Entry and Start System B



A

2.READ VALUE USING GTS (ENGINE SPEED)

B

8.CHECK DTC OUTPUT (ENTRY AND START SYSTEM (P033562))
2.READ VALUE USING GTS (ENGINE SPEED)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
750 to 850 rpm: Engine idling (shift lever in P, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Powertrain > Transmission > Data List
Tester Display
Engine Speed
50003 373 211
OK:

The GTS display changes correctly in response to the engine speed.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)
3.CHECK HARNESS AND CONNECTOR (TCM - ECM)

Pre-procedure1

a.

Disconnect the ECM connector.


b.

Disconnect the TCM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-16 (NEO) - D71-13 (NE) Always Below 1 Ω
A54-16 (NEO) or D71-13 (NE) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

Connect the TCM connector.


e.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.PERFORM REGISTRATION AND INITIALIZATION
5.PERFORM REGISTRATION AND INITIALIZATION

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (P033531)
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (P033531)
a.

Start the engine and wait for 5 seconds or more.


b.

Read the DTCs.

Powertrain > Transmission > Trouble Codes
50001 373

Result:
Result Proceed to
DTCs are not output A
P033531 is output B



A

END

B

7.REPLACE ECM
8.CHECK DTC OUTPUT (ENTRY AND START SYSTEM (P033562))
a.

Read the DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 454

Result:
Result Proceed to
DTCs are not output A
P033562 is output B



A

9.CHECK HARNESS AND CONNECTOR (TCM - ECM)

B

9.CHECK HARNESS AND CONNECTOR (TCM - ECM)

Pre-procedure1

a.

Disconnect the ECM connector.


b.

Disconnect the TCM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-16 (NEO) - D71-13 (NE) Always Below 1 Ω
A54-16 (NEO) or D71-13 (NE) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

Connect the TCM connector.


e.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

10.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT