Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0419699 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P084011  Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Ground  


DESCRIPTION

The TCM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P084011 Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Ground When 2 seconds or more have elapsed since engine start, a short to ground is detected in the oil pressure sensor circuit for 0.5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Oil pressure sensor

·

TCM


Comes on DTC stored SAE Code:
P0842

MONITOR DESCRIPTION

This DTC indicates a short to ground in the oil pressure sensor circuit. If there is a short to ground in the oil pressure sensor circuit, the TCM detects the malfunction, illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P084011.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C318995E52
1.094,2.802 2.781,3 1.688,0.198 10 false Oil Pressure Sensor 5.323,3.073 6.135,3.438 0.813,0.365 10 false TCM 1.094,2.656 1.552,2.854 0.458,0.198 10 false D47 5.323,2.906 6.042,3.198 0.719,0.292 10 false D71 4.906,2.156 5.521,2.354 0.615,0.198 10 false EPTO 4.906,1.604 5.521,1.802 0.615,0.198 10 false PTO 4.906,1.125 5.521,1.323 0.615,0.198 10 false VCPT 2.135,1.24 2.75,1.438 0.615,0.198 10 false VC 2.063,1.729 2.677,1.927 0.615,0.198 10 false PTO 2.156,2.271 2.771,2.469 0.615,0.198 10 false E2 2.469,2.167 3.083,2.365 0.615,0.198 10 false 1 2.469,1.604 3.083,1.802 0.615,0.198 10 false 2 2.469,1.125 3.083,1.323 0.615,0.198 10 false 3 4.604,1.125 5.219,1.323 0.615,0.198 10 false 49 4.615,1.615 5.229,1.813 0.615,0.198 10 false 50 4.615,2.156 5.229,2.354 0.615,0.198 10 false 48 5.583,0.948 6.198,1.146 0.615,0.198 10 false 5 V

CAUTION / NOTICE / HINT

CAUTION:
·
C328184

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328186

Do not perform a stall test if any wheel chock is out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328185

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.



NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:

A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.



Pre-procedure1

a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


Procedure1

c.

According to the display on the GTS, perform the Active Test.

Powertrain > Transmission > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the TC Terminal
·

Changes to the fluid temperature detection mode

·

Performs stall speed test

·

Performs secondary oil pressure test


ON or OFF
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P



d.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
3.4 to 4.2 MPa (34.7 to 42.8 kgf/cm2, 493 to 609 psi): D position stall test
-
Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

Post-procedure1

e.

None.


Result:
Result Proceed to
The value of Belt Clamping Force Sensor is 3.4 MPa or more, and 4.2 MPa or less A
The value of Belt Clamping Force Sensor is more than 4.2 MPa, or less than 3.4 MPa B


HINT:

3.4 MPa=34.7 kgf/cm2

3.4 MPa=493 psi

4.2 MPa=42.8 kgf/cm2

4.2 MPa=609 psi



A

2.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)

B

4.CHECK TCM (VCPT TERMINAL VOLTAGE)
2.READ VALUE USING GTS (BELT CLAMPING FORCE SENSOR)
CAUTION:

A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.



Pre-procedure1

a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


Procedure1

c.

According to the display on the GTS, perform the Active Test.

Powertrain > Transmission > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the TC Terminal
·

Changes to the fluid temperature detection mode

·

Performs stall speed test

·

Performs secondary oil pressure test


ON or OFF
(Vehicle Condition)

Ignition switch ON, engine stopped and shift lever in P



d.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Belt Clamping Force Sensor Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
2.4 to 3.2 MPa (24.5 to 32.6 kgf/cm2, 348 to 464 psi): R position stall test
-
Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Belt Clamping Force Sensor
50004 373 22 367

Post-procedure1

e.

None.


Result:
Result Proceed to
The value of Belt Clamping Force Sensor is 2.4 MPa or more, and 3.2 MPa or less A
The value of Belt Clamping Force Sensor is more than 3.2 MPa, or less than 2.4 MPa B


HINT:

2.4 MPa=24.5 kgf/cm2

2.4 MPa=348 psi

3.2 MPa=32.6 kgf/cm2

3.2 MPa=464 psi



A

3.REPLACE TCM

B

4.CHECK TCM (VCPT TERMINAL VOLTAGE)
3.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK TCM (VCPT TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the oil pressure sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D47-3 (VC) - D47-1 (E2) Ignition switch ON 4.75 to 5.25 V



Post-procedure1

d.

Turn the ignition switch off.


e.

Connect the oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - TCM)

NG

11.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - TCM)
5.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - TCM)

Pre-procedure1

a.

Disconnect the oil pressure sensor connector.


b.

Disconnect the TCM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D47-2 (PTO) - D71-50 (PTO) Always Below 1 Ω
D47-2 (PTO) or D71-50 (PTO) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

Connect the TCM connector.


e.

Connect the oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE OIL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OIL PRESSURE SENSOR - TCM)

6.REPLACE OIL PRESSURE SENSOR
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

Result:
Proceed to
NEXT



NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (P084011)
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (P084011)

Pre-procedure1

a.

Start the engine and wait for 5 seconds or more.


Procedure1

b.

Read the DTCs.

Powertrain > Transmission > Trouble Codes
50001 373

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P084011 is output B



A

END

B

10.REPLACE TCM
10.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - TCM)

Pre-procedure1

a.

Disconnect the oil pressure sensor connector.


b.

Disconnect the TCM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D47-3 (VC) - D71-49 (VCPT) Always Below 1 Ω
D47-1 (E2) - D71-48 (EPTO) Always Below 1 Ω
D47-3 (VC) or D71-49 (VCPT) - Body ground and other terminals Always 10 kΩ or higher
D47-1 (E2) or D71-48 (EPTO) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

Connect the TCM connector.


e.

Connect the oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

12.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OIL PRESSURE SENSOR - TCM)

12.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT