The transmission revolution sensor (NSS) detects the secondary pulley speed and sends it to the TCM.
The TCM determines the current gear ratio from the transmission revolution sensor (NSS) signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P274912 | Intermediate Shaft Speed Sensor "C" Circuit Short to Battery | The transmission revolution sensor (NSS) signal is normal but the transmission revolution sensor (NSS) output voltage is higher than 1.8 V for 4.5 seconds or more (1-trip detection logic). | ·
Wire harness or connector ·
Transmission revolution sensor (NSS) ·
TCM |
Comes on | DTC stored | SAE Code:
P07CA |
| P274914 | Intermediate Shaft Speed Sensor "C" Circuit Short to Ground or Open | The transmission revolution sensor (NSS) signal is normal but the transmission revolution sensor (NSS) output voltage is less than 0.2 V for 4.5 seconds or more (1-trip detection logic). | ·
Wire harness or connector ·
Transmission revolution sensor (NSS) ·
TCM |
Comes on | DTC stored | SAE Code:
P07C9 |
| P274931 | Intermediate Shaft Speed Sensor "C" No Signal | When the transmission revolution sensor (NOUT) signal indicates 350 rpm or more and the transmission revolution sensor (NT) signal indicates 780 rpm or more, the transmission revolution sensor (NSS) signal indicates less than 300 rpm for 5 seconds or more (1-trip detection logic). | ·
Wire harness or connector ·
Transmission revolution sensor (NSS) ·
TCM |
Comes on | DTC stored | SAE Code:
P2751 |
The TCM receives signals from the transmission revolution sensor (NSS) installed to the continuously variable transaxle and determines the secondary pulley speed in order to control the gear ratio.
If the TCM detects no signal from the transmission revolution sensor (NSS) even while the vehicle is being driven, it will determine that the transmission revolution sensor (NSS) is malfunctioning, illuminate the MIL and store a DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Perform the D Position Test inspection in Road Test.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P274912, P274914 or P274931.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Strictly observe posted speed limits, traffic laws and road conditions.
Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.
Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.
Do not operate the GTS while driving the vehicle.
Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| NSS Sensor Speed | Secondary pulley speed (NSS) | Min.: 0 rpm
Max.: 65535 rpm |
·
0 rpm: Vehicle stopped and shift lever in D ·
Equal to NO Sensor Speed: Vehicle being driven in belt mode |
- |
| NSS Sensor Voltage | Transmission revolution sensor (NSS) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P) | - |
| Tester Display |
|---|
| NSS Sensor Speed |
| NSS Sensor Voltage |
| Result | Proceed to |
|---|---|
| The value of NSS Sensor Voltage is 0.2 V or more, and 1.8 V or less | A |
| The value of NSS Sensor Voltage is more than 1.8 V, or less than 0.2 V | B |
A
B
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| NSS Sensor Speed | Secondary pulley speed (NSS) | Min.: 0 rpm
Max.: 65535 rpm |
·
0 rpm: Vehicle stopped and shift lever in D ·
Equal to NO Sensor Speed: Vehicle being driven in belt mode |
- |
| NSS Sensor Voltage | Transmission revolution sensor (NSS) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in N) | - |
| Tester Display |
|---|
| NSS Sensor Speed |
| NSS Sensor Voltage |
| Result | Proceed to |
|---|---|
| The value of NSS Sensor Voltage is 0.2 V or more, and 1.8 V or less | A |
| The value of NSS Sensor Voltage is more than 1.8 V, or less than 0.2 V | B |
A
B
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Pre-procedure1
Remove the transmission revolution sensor (NSS).
Connect the battery to the transmission revolution sensor (NSS) as shown in the illustration.
| *1 | Battery | *2 | Ammeter |
| *a | Component without harness connected
(Transmission Revolution Sensor (NSS)) |
*b | Magnet |
| *c | 5 mm or less | - | - |
Procedure1
Wave a magnet left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NSS) to output a high/low signal while measuring the current.
Make sure to wave the magnet during the inspection. The current will not change unless the magnet is moved as shown in the illustration.
Measure the current according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D63-1 (NSSO) - D63-2 (NSSB) | Low signal | 4 to 8 mA |
| D63-1 (NSSO) - D63-2 (NSSB) | High signal | 12 to 16 mA |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the transmission revolution sensor (NSS) connector.
Disconnect the TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D63-1 (NSSO) - D71-7 (NSSO) | Always | Below 1 Ω |
| D63-2 (NSSB) - D71-23 (NSSB) | Always | Below 1 Ω |
| D63-1 (NSSO) or D71-7 (NSSO) - Body ground and other terminals | Always | 10 kΩ or higher |
| D63-2 (NSSB) or D71-23 (NSSB) - Body ground and other terminals | Always | 10 kΩ or higher |
Post-procedure1
Connect the TCM connector.
Connect the transmission revolution sensor (NSS) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION