Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2020.03–2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0419699 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to M, it is possible to change the shift range between M1 and M10 using the shift lever. Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.

WIRING DIAGRAM

C318220E55
0.167,0.625 1.073,1.427 0.906,0.802 10 false from ECU-IGR NO. 1 Fuse 1.719,2.646 3.771,3.188 2.052,0.542 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 1.719,2.49 2.031,2.688 0.313,0.198 10 false H64 2.073,0.49 2.385,0.688 0.313,0.198 10 false IG 2.063,1.854 2.375,2.042 0.313,0.188 10 false E 3.271,0.5 3.583,0.688 0.313,0.188 10 false S 3.031,1.177 3.646,1.375 0.615,0.198 10 false SFTU 3.031,1.854 3.646,2.052 0.615,0.198 10 false SFTD 5.521,0.5 5.833,0.688 0.313,0.188 10 false B 5.51,1.167 6.125,1.365 0.615,0.198 10 false SFTU 5.521,1.854 6.135,2.052 0.615,0.198 10 false SFTD 5.844,2.5 6.385,2.844 0.542,0.344 10 false D71 5.844,2.656 6.25,3.271 0.406,0.615 10 false TCM 1.854,0.49 2.01,0.688 0.156,0.198 10 false 4 1.865,1.854 2.177,2.052 0.313,0.198 10 false 2 3.5,1.854 3.813,2.052 0.313,0.198 10 false 3 3.5,1.177 3.813,1.375 0.313,0.198 10 false 1 3.479,0.531 3.792,0.729 0.313,0.198 10 false 5 5.25,0.49 5.563,0.688 0.313,0.198 10 false 14 5.25,1.167 5.563,1.365 0.313,0.198 10 false 28 5.25,1.854 5.563,2.052 0.313,0.198 10 false 27 6.25,1.01 6.708,1.208 0.458,0.198 10 false 12 V 6.25,1.688 6.708,1.885 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Read the DTCs using the GTS.

Powertrain > Transmission > Trouble Codes
50001 373

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))

B

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Transmission control switch status ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (S Range)
50003 373 27

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

3.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)

B

8.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
3.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" or "+" shift paddle switch operated

·

OFF: Shift lever not held in "+" and "+" shift paddle switch released


-
Sport Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" or "-" shift paddle switch operated

·

OFF: Shift lever not held in "-" and "-" shift paddle switch released


-
Powertrain > Transmission > Data List
Tester Display
Sport Shift Up SW
Sport Shift Down SW
50003 373 26,25

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

B

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C57
1.292,1.729 1.646,1.313 true 2.698,1.729 2.313,1.302 true 1.979,1.729 1.958,1.333 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.948,1.76 2.104,1.958 0.156,0.198 10 false E 1.104,1.76 1.719,1.958 0.615,0.198 10 false SFTD 2.542,1.76 3.156,1.958 0.615,0.198 10 false SFTU
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the shift lock control unit assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in "+" Below 1 Ω
1 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-" Below 1 Ω
3 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher



c.

Connect the shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - BODY GROUND)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - BODY GROUND)
a.

Disconnect the shift lock control unit assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G64-2 (E) - Body ground Always Below 1 Ω



c.

Connect the shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D71-28 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
D71-28 (SFTU) - Body ground Shift lever in M 10 kΩ or higher
D71-27 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
D71-27 (SFTD) - Body ground Shift lever in M 10 kΩ or higher



c.

Connect the TCM connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

7.REPLACE TCM

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL

Result:
Proceed to
NEXT



NEXT

8.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C12
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 *a 1.906,1.802 2.375,2 0.469,0.198 10 IG 0.646,1.771 1.021,1.979 0.375,0.208 10 S
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the shift lock control unit assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M 10 kΩ or higher



c.

Connect the shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

9.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

9.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE)
a.

Disconnect the shift lock control unit assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H64-4 (IG) - Body ground Ignition switch ON 11 to 14 V
H64-4 (IG) - Body ground Ignition switch off Below 1 V



c.

Connect the shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

NG

CHECK POWER SOURCE CIRCUIT (SHIFT LOCK CONTROL UNIT ASSEMBLY)

10.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)
a.

Disconnect the TCM connector.


b.

Disconnect the shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H64-5 (S) - D71-14 (B) Always Below 1 Ω
H64-5 (S) or D71-14 (B) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the TCM connector.


e.

Connect the shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

11.REPLACE TCM

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL

Result:
Proceed to
NEXT



NEXT