Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  ECU Power Source Circuit  


DESCRIPTION

If the ignition switch is ON, the hybrid vehicle control ECU applies current to the MREL terminal to turn the IGCT-MAIN relay on. This supplies power to the +B1 and +B2 terminals.

WIRING DIAGRAM

A460069E02
0.115,3.375 1.615,3.573 1.5,0.198 10 false from Auxiliary Battery 2.344,1.969 4.354,2.219 2.01,0.25 10 false No. 5 Relay Block Assembly 1.313,1.219 1.469,1.417 0.156,0.198 10 false 5 1.313,0.802 1.469,1 0.156,0.198 10 false 5 1.802,0.708 1.958,0.906 0.156,0.198 10 false 3 1.802,1.125 1.958,1.323 0.156,0.198 10 false 2 2.604,1.125 2.76,1.323 0.156,0.198 10 false 1 2.563,0.708 2.719,0.906 0.156,0.198 10 false 5 4.135,0.698 4.292,0.896 0.156,0.198 10 false 1 4.542,0.698 4.698,0.896 0.156,0.198 10 false 2 4.104,0.969 4.729,1.156 0.625,0.188 10 false PM-IGCT 6.313,0.396 6.771,0.594 0.458,0.198 10 false +B1 6.021,0.167 6.167,0.365 0.146,0.198 10 false 7 6.01,1.604 6.167,1.802 0.156,0.198 10 false 1 6.021,0.615 6.177,0.813 0.156,0.198 10 false 8 5.375,3.156 7.104,3.5 1.729,0.344 10 false Hybrid Vehicle Control ECU 6.323,0.823 6.781,1.021 0.458,0.198 10 false +B2 6.313,1.25 6.927,1.448 0.615,0.198 10 false MREL 5.948,2.688 6.25,2.875 0.302,0.188 10 false H44 5.948,2.25 6.26,2.438 0.313,0.188 10 false A68 0.427,2.146 0.76,2.344 0.333,0.198 10 false O90 5.979,1.031 6.229,1.229 0.25,0.198 10 false 47 5.979,2.052 6.219,2.281 0.24,0.229 10 false 10 5.969,2.479 6.198,2.729 0.229,0.25 10 false 15 6.313,1.833 6.667,2.021 0.354,0.188 10 false E12 6.313,2.26 6.667,2.448 0.354,0.188 10 false E01 6.323,2.688 6.677,2.875 0.354,0.188 10 false E1 1.49,2.604 3.042,2.813 1.552,0.208 10 false Fusible Link Assembly 0.771,2.135 0.927,2.333 0.156,0.198 10 false 1 3.083,0.802 3.24,1 0.156,0.198 10 false 5 3.76,0.813 3.917,1.01 0.156,0.198 10 false 5 4.885,0.792 5.042,0.99 0.156,0.198 10 false 5 4.885,1.219 5.042,1.417 0.156,0.198 10 false 5 5.938,1.823 6.24,2.01 0.302,0.188 10 false H44 5.938,1.229 6.24,1.417 0.302,0.188 10 false H44 5.938,0.802 6.24,0.99 0.302,0.188 10 false H44 5.927,0.375 6.229,0.563 0.302,0.188 10 false H44 0.615,2.615 1.354,2.792 0.74,0.177 10 false IGCT-MAIN 1.865,1.552 2.604,1.729 0.74,0.177 10 false IGCT-MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU (+B1, +B2 VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

A458550C16
4.688,0.25 5.115,0.552 0.427,0.302 5.552,2.344 4.969,1.271 true 4.375,2.333 4.833,1.26 true 0.313,0.24 0.625,0.396 0.313,0.156 10 false *a 4.802,0.344 5.438,0.594 0.635,0.25 10 false H44 4.167,2.354 4.802,2.604 0.635,0.25 10 false +B2 5.563,2.354 6.198,2.604 0.635,0.25 10 false +B1
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H44-7 (+B1) - Body ground Ignition switch ON 11 to 14 V
H44-8 (+B2) - Body ground Ignition switch ON 11 to 14 V



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

NG

3.CHECK HYBRID VEHICLE CONTROL ECU (MREL VOLTAGE)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the A68 and H44 hybrid vehicle control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

A368649C38
0.385,0.74 0.885,1.052 0.5,0.313 3.573,0.74 4.073,1.052 0.5,0.313 4.094,1.479 4.406,0.865 true 2.167,1.479 2.521,0.885 true 4.896,1.5 4.615,0.958 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 0.531,0.823 0.844,0.979 0.313,0.156 10 false A68 3.719,0.833 4.031,0.99 0.313,0.156 10 false H44 4.927,1.5 5.24,1.656 0.313,0.156 10 false E1 1.979,1.5 2.292,1.656 0.313,0.156 10 false E01 3.906,1.5 4.219,1.656 0.313,0.156 10 false E12
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H44-15 (E1) - Body ground Always Below 1 Ω
A68-10 (E01) - Body ground Always Below 1 Ω
H44-1 (E12) - Body ground Always Below 1 Ω



c.

Reconnect the A68 and H44 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HYBRID VEHICLE CONTROL ECU (MREL VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

A458550C17
4.656,0.25 5.125,0.552 0.469,0.302 4.385,2.375 4.938,1.635 true 0.313,0.24 0.625,0.396 0.313,0.156 10 false *a 4.792,0.333 5.427,0.583 0.635,0.25 10 false H44 4.104,2.396 4.74,2.646 0.635,0.25 10 false MREL
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H44-47 (MREL) - Body ground Ignition switch ON 11 to 14 V



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

4.CHECK FUSE (PM-IGCT)

NG

4.CHECK FUSE (PM-IGCT)
a.
A460070C01
1.333,1.01 0.74,1.563 true 0.167,0.115 0.479,0.271 0.313,0.156 10 false *1 0.604,1.573 0.917,1.729 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 PM-IGCT Fuse


Remove the PM-IGCT fuse from the No. 5 relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PM-IGCT fuse Always Below 1 Ω



c.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

5.INSPECT RELAY (IGCT-MAIN)

NG

10.CHECK HARNESS OR CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
5.INSPECT RELAY (IGCT-MAIN)
a.
A458553C01
2.635,1.74 2.531,1.74 2.531,1.74 2.042,2.292 true 0.281,0.167 0.594,0.323 0.313,0.156 10 false *1 2.708,1.688 3.021,1.844 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 IGCT-MAIN Relay


Remove the IGCT-MAIN relay from the No. 5 relay block assembly.


b.
A253297C01
0.146,0.056 0.409,0.261 0.263,0.205 10 *1
*1 IGCT-MAIN Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the IGCT-MAIN relay.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

NG

REPLACE RELAY (IGCT-MAIN)

6.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H44 hybrid vehicle control ECU connectors.


b.

Remove the PM-IGCT fuse from the No. 5 relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

A460071C01
4.969,0.385 5.417,0.688 0.448,0.302 5.25,1.313 5.479,2.083 true 5.115,1.323 4.75,2.083 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *1 1.115,0.51 1.427,0.667 0.313,0.156 10 false *2 3.615,0.198 3.927,0.354 0.313,0.156 10 false *a 4.594,2.094 4.958,2.281 0.365,0.188 10 false +B1 5.406,2.094 5.771,2.281 0.365,0.188 10 false +B2 5.094,0.469 5.427,0.719 0.333,0.25 10 false H44
*1 No. 5 Relay Block Assembly *2 PM-IGCT Fuse Holder
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H44-7 (+B1) - 2 (PM-IGCT fuse holder) Always Below 1 Ω
H44-8 (+B2) - 2 (PM-IGCT fuse holder) Always Below 1 Ω



d.

Install the PM-IGCT fuse.


e.

Reconnect the H44 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY)
a.

Remove the PM-IGCT fuse and IGCT-MAIN relay from the No. 5 relay block assembly.


b.
A458557C01
0.104,0.094 0.417,0.25 0.313,0.156 10 false *1 0.823,0.688 1.135,0.844 0.313,0.156 10 false *2 0.354,1.979 0.667,2.135 0.313,0.156 10 false *3
*1 No. 5 Relay Block Assembly
*2 PM-IGCT Fuse Holder
*3 IGCT-MAIN Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT-MAIN relay holder) - 1 (PM-IGCT fuse holder) Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
3 (PM-IGCT fuse holder) - Body ground Always 11 to 14 V



c.

Install the PM-IGCT fuse and IGCT-MAIN relay.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 5 RELAY BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 5 RELAY BLOCK ASSEMBLY)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Remove the IGCT-MAIN relay from the No. 5 relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

A458552C02
4.906,0.583 5.385,0.927 0.479,0.344 5.365,2.438 5.115,1.938 true 0.646,0.188 0.958,0.344 0.313,0.156 10 false *1 0.802,1.625 1.115,1.781 0.313,0.156 10 false *2 3.76,0.208 4.073,0.365 0.313,0.156 10 false *a 5.406,2.469 6.031,2.698 0.625,0.229 10 false MREL 5.042,0.698 5.667,0.927 0.625,0.229 10 false H44
*1 No. 5 Relay Block Assembly *2 IGCT-MAIN Relay Holder
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H44-47 (MREL) - 1 (IGCT-MAIN relay holder) Always Below 1 Ω
H44-47 (MREL) or 1 (IGCT-MAIN relay holder) - Body ground and other terminals Always 10 kΩ or higher



d.

Install the IGCT-MAIN relay.


e.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - BODY GROUND)
a.

Remove the IGCT-MAIN relay from the No. 5 relay block assembly.


b.
A458554C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *1 0.823,1.656 1.135,1.813 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 IGCT-MAIN Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT-MAIN relay holder) - Body ground Always Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS OR CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Remove the PM-IGCT fuse from the No. 5 relay block assembly.


b.

Disconnect the H44 hybrid vehicle control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

A460071C01
4.969,0.385 5.417,0.688 0.448,0.302 5.25,1.313 5.479,2.083 true 5.115,1.323 4.75,2.083 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *1 1.115,0.51 1.427,0.667 0.313,0.156 10 false *2 3.615,0.198 3.927,0.354 0.313,0.156 10 false *a 4.594,2.094 4.958,2.281 0.365,0.188 10 false +B1 5.406,2.094 5.771,2.281 0.365,0.188 10 false +B2 5.094,0.469 5.427,0.719 0.333,0.25 10 false H44
*1 No. 5 Relay Block Assembly *2 PM-IGCT Fuse Holder
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H44-7 (+B1) or 2 (PM-IGCT fuse holder) - Body ground and other terminals Always 10 kΩ or higher
H44-8 (+B2) or 2 (PM-IGCT fuse holder) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the H44 hybrid vehicle control ECU connectors.


e.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (PM-IGCT)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PM-IGCT)