Home › Vehicle Interior › LIGHTING (INT) › VANITY LIGHT SWITCH
RM36W0E _58 Vehicle Interior _087823 LIGHTING (INT) _0420210 VANITY LIGHT SWITCH G

LIGHTING (INT)  VANITY LIGHT SWITCH  INSPECTION  


PROCEDURE

Hide 74310 1.INSPECT VISOR ASSEMBLY RH

a.
E224622C17
2.5,0.563 3,0.813 0.5,0.25 1.969,2.917 2.385,2.5 true 1.167,3.917 1.167,3.583 false 0.542,3.156 0.542,2.823 false 0.833,1.323 1.24,1.031 true 2.688,1.333 2.292,1.042 true 0.896,0.125 1.167,0.333 0.271,0.208 10 false *a 0.49,3.208 0.76,3.417 0.271,0.208 10 false *b 1.115,3.948 1.385,4.156 0.271,0.208 10 false *c 2.427,2.375 2.698,2.583 0.271,0.208 10 false *d 0.688,1.271 0.958,1.479 0.271,0.208 10 false E 2.74,1.25 3.01,1.458 0.271,0.208 10 false +B 2.667,0.594 2.938,0.802 0.271,0.208 10 false V1
*a Component without harness connected
(Visor Assembly RH)
*b Visor up
*c Visor down
*d Mirror Cover


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-2(+B) - V1-1(E) Visor up 10 kΩ or higher
V1-2(+B) - V1-1(E) Mirror cover fully closed with visor down 10 kΩ or higher
V1-2(+B) - V1-1(E) Mirror cover fully open with visor down Below 1 Ω


If the result is not as specified, replace the visor assembly RH.



Hide 74320 2.INSPECT VISOR ASSEMBLY LH

a.
E224621C17
2.479,0.365 2.979,0.615 0.5,0.25 1.333,2.99 1.125,2.667 true 3,3.146 3,2.813 false 2.333,3.917 2.333,3.583 false 0.833,1.229 1.219,1 true 2.594,1.24 2.25,0.99 true 0.896,0.115 1.167,0.323 0.271,0.208 10 false *a 2.958,3.198 3.229,3.406 0.271,0.208 10 false *b 2.271,3.958 2.542,4.167 0.271,0.208 10 false *c 0.938,2.552 1.208,2.76 0.271,0.208 10 false *d 0.677,1.167 0.948,1.375 0.271,0.208 10 false E 2.646,1.167 2.917,1.375 0.271,0.208 10 false +B 2.635,0.396 2.906,0.604 0.271,0.208 10 false V2
*a Component without harness connected
(Visor Assembly LH)
*b Visor up
*c Visor down
*d Mirror Cover


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-2(+B) - V2-1(E) Visor up 10 kΩ or higher
V2-2(+B) - V2-1(E) Mirror cover fully closed with visor down 10 kΩ or higher
V2-2(+B) - V2-1(E) Mirror cover fully open with visor down Below 1 Ω


If the result is not as specified, replace the visor assembly LH.