Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420272 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  DATA LIST / ACTIVE TEST  


DATA LIST (BRAKE)


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Operate the GTS to read the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
-
·

Displays a positive value during deceleration/acceleration

·

During deceleration/acceleration: Changes continuously


FL Wheel Acceleration Front wheel LH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
-
·

Displays a positive value during deceleration/acceleration

·

During deceleration/acceleration: Changes continuously


RR Wheel Acceleration Rear wheel RH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
-
·

Displays a positive value during deceleration/acceleration

·

During deceleration/acceleration: Changes continuously


RL Wheel Acceleration Rear wheel LH acceleration Min.: -200.840 m/s2
Max.: 199.271 m/s2
-
·

Displays a positive value during deceleration/acceleration

·

During deceleration/acceleration: Changes continuously


Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa
Max.: 23.99 MPa
Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Zero Point of M/C Memorized zero value Min.: -12.5 MPa
Max.: 12.4 MPa
- -
Master Cylinder Sensor Temperature Master cylinder pressure sensor temperature Min.: -80°C
Max.: 175°C
Displays temperature master cylinder pressure sensor -
M/C Sensor Grade Master cylinder pressure sensor change (value detected by ECU) Min.: -30 MPa/s
Max.: 225 MPa/s
Brake pedal released or pedal held at constant position: 0 MPa/s When brake pedal is being operated: Changes in proportion with the pedal movement speed
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Zero Point of Decele2 Memorized zero value (lateral G) Min.: -25.105 m/s2
Max.: 24.908 m/s2
- -
Zero Point of Decele Memorized zero value (forward and rearward G) Min.: -25.105 m/s2
Max.: 24.908 m/s2
- -
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate Sensor Memorized zero value Min.: -128°/s
Max.: 127°/s
After completing zero point calibration: 0° -
Steering Angle Value Steering sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0°
-
Zero Point of Steering Angle Memorized zero value Min.: -3276.8°
Max.: 3276.7°
- -
MT Voltage Value ABS motor drive voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to the ABS motor) from the skid control ECU (brake actuator assembly) to the ABS motor relay


Solenoid Power Supply Voltage Solenoid power supply voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to each solenoid) from the skid control ECU (brake actuator assembly) to the ABS solenoid relay


Vehicle Speed Maximum wheel speed sensor reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Engine Revolutions Engine speed Min.: 0 rpm
Max.: 65535 rpm
Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%
Max.: 127.5%
Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Real Engine Torque Powertrain drive torque Min.: -1024.000 Nm
Max.: 1023.000 Nm
- -
Gear Position Gear position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R Actual gear position -
Shift Lever Position Shift lever position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input Actual shift lever position -
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) /
Not defined /
VSC OFF mode (TRC(TRAC) OFF/VSC OFF)
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
FR Target Oil Pressure Front wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
FL Target Oil Pressure Front wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
RR Target Oil Pressure Rear wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
RL Target Oil Pressure Rear wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
Vehicle Speed Maximum wheel speed sensor reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle acceleration Min.: -25.105 m/s2
Max.: 24.908 m/s2
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During driving: Changes in proportion with vehicle acceleration/deceleration
Vehicle Stop Time from IG ON Time vehicle stopped after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Travel Distance from IG ON Driving time after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Elapsed Time Time elapsed after ignition switch turned to ON Min.: 0.00 s
Max.: 100661.760 s
- -
Stop Light SW Stop light switch assembly
(STP terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:

The brake pedal state is determined using the voltage at terminal STP


Reverse Position Switch Reverse position switch OFF / ON OFF: Reverse position switch OFF
ON: Reverse position switch ON
-
Inspection Mode Inspection mode OFF / ON OFF: Normal mode
ON: Inspection mode
HINT:

Refer to utility for details on how to enter inspection mode*1


TRC(TRAC) Control TRC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Engine Control TRC engine control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Brake Control TRC brake control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel ABS Ctrl Status Front wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
HAB Control High power assist brake status OFF / ON OFF: During not control
ON: During control
-
BA Ctrl Status BA control status OFF / ON OFF: During not control
ON: During control
-
PBA Ctrl Status PBA control status OFF / ON OFF: During not control
ON: During control
-
Stop Light Relay State for ECU Control Semiconductor PWR integration ECU status (STPO terminal output) (value detected by ECU) OFF / ON OFF: Semiconductor PWR integration ECU not operating
ON: Semiconductor PWR integration ECU operating
-
Solenoid State for ECU Control ABS solenoid relay status (for ECU control) OFF / ON OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating
-
Motor State for ECU Control ABS motor relay status (for ECU control) OFF / ON OFF: ABS motor relay not operating
ON: ABS motor relay operating
-
Dealer Mode Dealer Mode (Signal Check mode or Calibration mode) status OFF / ON OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode)
HINT:
·

for details on Dealer Mode (Signal Check), refer to test mode procedure*2

·

for details on Dealer Mode (Calibration), refer to utility*3



Zero Point Memory State of Steering Angle Sensor Steering sensor zero point memorization status Zero point is not memorized / Zero point is memorized -
HINT:

The steering sensor zero point is acquired when the vehicle is being driven in a straight line at a speed of 15 km/h (9 mph) or more for approximately 1 second


TRC(TRAC)/VSC OFF SW VSC OFF switch (combination switch assembly) (CSW terminal input) OFF / ON OFF: VSC OFF switch (combination switch assembly) OFF
ON: VSC OFF switch (combination switch assembly) ON
HINT:

The VSC OFF switch (combination switch assembly) state is determined using the voltage at terminal CSW


IGP_PT1 IGP_PT1 status OFF / ON OFF: IGP_PT1 OFF
ON: IGP_PT1 ON
-
IGP_PT2 IGP_PT2 status OFF / ON OFF: IGP_PT2 OFF
ON: IGP_PT2 ON
-
FR Wheel Rotatory direction for front wheel RH Forward / Back - -
FL Wheel Rotatory direction for front wheel LH Forward / Back - -
RR Wheel Rotatory direction for rear wheel RH Forward / Back - -
RL Wheel Rotatory direction for rear wheel LH Forward / Back - -
FR Speed Open Front speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C050614, C14E314
FL Speed Open Front speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C050014, C14E014
RR Speed Open Rear speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C051214, C14E914
RL Speed Open Rear speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C050C14, C14E614
EFI Communication Open ECM communication open detection Under intermittent / Normal Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected
·

Related Vehicle Control History (RoB): X2079

·

Related DTC: U010087


Yaw Rate Open Yaw rate sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: U012587
Deceleration Open Acceleration sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: U012587
Steering Open Steering sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: U012687
Master Cylinder Open Master cylinder pressure sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C054031
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C05061F, C14E314
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C05001F, C14E014
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C05121F, C14E914
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C050C1F, C14E614
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Under intermittent / Normal Under intermittent: Noise detected
Normal: Noise not detected
Related DTC: C05401F
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C14D71C
EFI Communication Invalid ECM communication invalid detection Under intermittent / Normal Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected
·

Related Vehicle Control History (RoB): X2079

·

Related DTC: U010087


Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C054049
Solenoid Power Supply Open Solenoid power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C143A7F
Motor Power Supply Open Motor power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C052F14
Stop Switch Open Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
Related DTC: C13807E, C13807F, P057113
Air Bag ECU Communication Open Airbag sensor assembly open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
·

Related Vehicle Control History (RoB): X2086

·

Related DTC: U015187


ABS Solenoid (SRLR) Rear pressure reduction solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRLH) Rear pressure holding solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRRR) Rear pressure reduction solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRRH) Rear pressure holding solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFLR) Front pressure reduction solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFLH) Front pressure holding solenoid LH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFRR) Front pressure reduction solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFRH) Front pressure holding solenoid RH status OFF / ON OFF: Not operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


TRC(TRAC)/VSC Solenoid (SM2) Master cylinder cut solenoid (Brake Pressure Control Solenoid "B") status OFF / ON OFF: Not operating
ON: Operating (pressure regulation)
HINT:

Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor


TRC(TRAC)/VSC Solenoid (SM1) Master cylinder cut solenoid (Brake Pressure Control Solenoid "A") status OFF / ON OFF: Not operating
ON: Operating (pressure regulation)
HINT:

Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor


ABS Motor Relay Motor relay OFF / ON OFF: Motor relay off
ON: Motor relay on
-
Solenoid Relay Solenoid relay OFF / ON OFF: Solenoid relay off
ON: Solenoid relay on
-
STPO Semiconductor PWR integration ECU (STPO terminal output) OFF / ON OFF: Semiconductor PWR integration ECU off (Stop light off)
ON: Semiconductor PWR integration ECU on (Stop light on)
HINT:

When STPO is ON, the Semiconductor PWR integration ECU turns ON and the stop lights illuminate


IGR Voltage IGR terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
+BS Voltage +BS terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal +BS (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)


+BM Voltage BM terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal BM (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)





DATA LIST (STEERING ANGLE SENSOR)


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Operate the GTS to read the Data List.

Chassis > Steering Angle Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Operate the GTS to perform the Active Test.

Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
EBS Relay - - - Not applicable to this vehicle
ABS Solenoid Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR)
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P*1

·

Shift lever is in N*2

·

Apply the parking brake


HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Refer to on-vehicle inspection for the brake actuator*
VSC Solenoid Master cylinder cut solenoid (SMF (SM1), SMR (SM2)) Solenoid Start (Activate)
Solenoid SMF / SMR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P*1

·

Shift lever is in N*2

·

Apply the parking brake


HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Check that the GTS display for the solenoid (SM1 or SM2) changes to ON/OFF during Solenoid Start (Activate)
Motor Relay ABS motor relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Refer to on-vehicle inspection for the brake actuator*3
Solenoid Relay Solenoid relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Perform the Active Test and check that the voltage displayed for the solenoid power supply voltage Data List item changes.
Stop Lamp Relay Stop light switch assembly (STPO terminal output) OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


Check that the stop light switch assembly (STPO terminal output) turns ON when the brake pedal is released, the stop lights illuminate, and the "stop light relay" and "STPO" Data List items switch to ON.