Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0420300 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


B150964N38
3.354,0.083 3.76,0.323 0.406,0.24 3.479,0.125 3.771,0.323 0.292,0.198 10 false K5

a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
K5-11 (B) - K5-12 (GND) Power supply Ignition switch off 11 to 14 V
K5-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the K5 multiplex network master switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
K5-15 (DOWN) - K5-12 (GND) Power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or not pulled 11 to 14 V
K5-15 (DOWN) - K5-12 (GND) Power window motor DOWN output Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
K5-20 (UP) - K5-12 (GND) Power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or not pulled 11 to 14 V
K5-20 (UP) - K5-12 (GND) Power window motor UP output Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


B429631N74
3.458,0.208 3.875,0.479 0.417,0.271 3.583,0.26 3.896,0.458 0.313,0.198 10 false L6

a.

Disconnect the L6 power window regulator switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
L6-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the L6 power window regulator switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
L6-5 (UP) - L6-7 (GND) Power window motor UP output Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
L6-5 (UP) - L6-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
L6-5 (UP) - L6-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window fully open 11 to 14 V
L6-5 (UP) - L6-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
L6-5 (UP) - L6-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
L6-4 (DOWN) - L6-7 (GND) Power window motor DOWN output Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
L6-4 (DOWN) - L6-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
L6-4 (DOWN) - L6-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
L6-4 (DOWN) - L6-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
L6-4 (DOWN) - L6-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window fully open 11 to 14 V
L6-8 (AUTO) - L6-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window fully open 11 to 14 V
L6-8 (AUTO) - L6-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
L6-8 (AUTO) - L6-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
L6-8 (AUTO) - L6-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
L6-8 (AUTO) - L6-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
L6-8 (AUTO) - L6-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)


B429631N50
3.458,0.208 3.875,0.479 0.417,0.271 3.594,0.26 3.906,0.458 0.313,0.198 10 false N3

a.

Disconnect the N3 rear power window regulator switch assembly (for LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
N3-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the N3 rear power window regulator switch assembly (for LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
N3-5 (UP) - N3-7 (GND) Power window motor UP output Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
N3-5 (UP) - N3-7 (GND) Power window motor UP output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
N3-5 (UP) - N3-7 (GND) Power window motor UP output Ignition switch ON, rear LH door power window fully open 11 to 14 V
N3-5 (UP) - N3-7 (GND) Power window motor UP output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
N3-5 (UP) - N3-7 (GND) Power window motor UP output Ignition switch ON, rear LH door power window fully closed 11 to 14 V
N3-4 (DOWN) - N3-7 (GND) Power window motor DOWN output Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
N3-4 (DOWN) - N3-7 (GND) Power window motor DOWN output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
N3-4 (DOWN) - N3-7 (GND) Power window motor DOWN output Ignition switch ON, rear LH door power window fully closed 11 to 14 V
N3-4 (DOWN) - N3-7 (GND) Power window motor DOWN output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
N3-4 (DOWN) - N3-7 (GND) Power window motor DOWN output Ignition switch ON, rear LH door power window fully open 11 to 14 V
N3-8 (AUTO) - N3-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear LH door power window fully open 11 to 14 V
N3-8 (AUTO) - N3-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
N3-8 (AUTO) - N3-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear LH door power window fully closed 11 to 14 V
N3-8 (AUTO) - N3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear LH door power window fully closed 11 to 14 V
N3-8 (AUTO) - N3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
N3-8 (AUTO) - N3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear LH door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)


B429631N51
3.458,0.208 3.875,0.479 0.417,0.271 3.583,0.26 3.896,0.458 0.313,0.198 10 false M3

a.

Disconnect the M3 rear power window regulator switch assembly (for RH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
M3-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the M3 rear power window regulator switch assembly (for RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M3-5 (UP) - M3-7 (GND) Power window motor UP output Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
M3-5 (UP) - M3-7 (GND) Power window motor UP output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
M3-5 (UP) - M3-7 (GND) Power window motor UP output Ignition switch ON, rear RH door power window fully open 11 to 14 V
M3-5 (UP) - M3-7 (GND) Power window motor UP output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
M3-5 (UP) - M3-7 (GND) Power window motor UP output Ignition switch ON, rear RH door power window fully closed 11 to 14 V
M3-4 (DOWN) - M3-7 (GND) Power window motor DOWN output Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
M3-4 (DOWN) - M3-7 (GND) Power window motor DOWN output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
M3-4 (DOWN) - M3-7 (GND) Power window motor DOWN output Ignition switch ON, rear RH door power window fully closed 11 to 14 V
M3-4 (DOWN) - M3-7 (GND) Power window motor DOWN output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
M3-4 (DOWN) - M3-7 (GND) Power window motor DOWN output Ignition switch ON, rear RH door power window fully open 11 to 14 V
M3-8 (AUTO) - M3-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear RH door power window fully open 11 to 14 V
M3-8 (AUTO) - M3-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
M3-8 (AUTO) - M3-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear RH door power window fully closed 11 to 14 V
M3-8 (AUTO) - M3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear RH door power window fully closed 11 to 14 V
M3-8 (AUTO) - M3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
M3-8 (AUTO) - M3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear RH door power window fully open 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


B574782N01
2.156,0.823 2.552,1.063 0.396,0.24 2.26,0.865 2.583,1.083 0.323,0.219 10 false K7

a.

Disconnect the K7 power window regulator motor assembly (for driver door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
K7-1 (GND) - Body ground Ground Always Below 1 Ω
K7-2 (B) - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the K7 power window regulator motor assembly (for driver door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
K7-7 (DOWN) - K7-1 (GND) Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
K7-7 (DOWN) - K7-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
K7-7 (DOWN) - K7-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window fully closed 11 to 14 V
K7-7 (DOWN) - K7-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
K7-7 (DOWN) - K7-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window fully open 11 to 14 V
K7-10 (UP) - K7-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
K7-10 (UP) - K7-1 (GND) Power window motor UP input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
K7-10 (UP) - K7-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
K7-10 (UP) - K7-1 (GND) Power window motor UP input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
K7-10 (UP) - K7-1 (GND) Power window motor UP input Ignition switch ON, driver door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)


B574782N03
2.156,0.823 2.552,1.063 0.396,0.24 2.271,0.865 2.594,1.083 0.323,0.219 10 false L7

a.

Disconnect the L7 power window regulator motor assembly (for front passenger door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
L7-1 (GND) - Body ground Ground Always Below 1 Ω
L7-2 (B) - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the L7 power window regulator motor assembly (for front passenger door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
L7-4 (AUTO) - L7-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
L7-4 (AUTO) - L7-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
L7-4 (AUTO) - L7-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
L7-4 (AUTO) - L7-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
L7-4 (AUTO) - L7-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
L7-4 (AUTO) - L7-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully open 11 to 14 V
L7-7 (DOWN) - L7-1 (GND) Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
L7-7 (DOWN) - L7-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
L7-7 (DOWN) - L7-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
L7-7 (DOWN) - L7-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
L7-7 (DOWN) - L7-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window fully open 11 to 14 V
L7-10 (UP) - L7-1 (GND) Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
L7-10 (UP) - L7-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
L7-10 (UP) - L7-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
L7-10 (UP) - L7-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
L7-10 (UP) - L7-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)


B286758N34
2.292,0.771 2.656,0.99 0.365,0.219 2.385,0.802 2.771,1.01 0.385,0.208 10 false N4

a.

Disconnect the N4 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
N4-1 (GND) - Body ground Ground Always Below 1 Ω
N4-2 (B) - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the N4 power window regulator motor assembly (for rear LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
N4-4 (AUTO) - N4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
N4-4 (AUTO) - N4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
N4-4 (AUTO) - N4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
N4-4 (AUTO) - N4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
N4-4 (AUTO) - N4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
N4-4 (AUTO) - N4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully open 11 to 14 V
N4-7 (DOWN) - N4-1 (GND) Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
N4-7 (DOWN) - N4-1 (GND) Power window motor DOWN input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
N4-7 (DOWN) - N4-1 (GND) Power window motor DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
N4-7 (DOWN) - N4-1 (GND) Power window motor DOWN input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
N4-7 (DOWN) - N4-1 (GND) Power window motor DOWN input Ignition switch ON, rear LH door power window fully open 11 to 14 V
N4-10 (UP) - N4-1 (GND) Power window motor UP input Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
N4-10 (UP) - N4-1 (GND) Power window motor UP input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
N4-10 (UP) - N4-1 (GND) Power window motor UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
N4-10 (UP) - N4-1 (GND) Power window motor UP input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
N4-10 (UP) - N4-1 (GND) Power window motor UP input Ignition switch ON, rear LH door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)


B574782N04
2.219,0.771 2.615,1.01 0.396,0.24 2.323,0.813 2.635,1.052 0.313,0.24 10 false M4

a.

Disconnect the M4 power window regulator motor assembly (for rear RH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
M4-1 (GND) - Body ground Ground Always Below 1 Ω
M4-2 (B) - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the M4 power window regulator motor assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M4-4 (AUTO) - M4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
M4-4 (AUTO) - M4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
M4-4 (AUTO) - M4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
M4-4 (AUTO) - M4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
M4-4 (AUTO) - M4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
M4-4 (AUTO) - M4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully open 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) Power window motor DOWN input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
M4-7 (DOWN) - M4-1 (GND) Power window motor DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) Power window motor DOWN input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
M4-7 (DOWN) - M4-1 (GND) Power window motor DOWN input Ignition switch ON, rear RH door power window fully open 11 to 14 V
M4-10 (UP) - M4-1 (GND) Power window motor UP input Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
M4-10 (UP) - M4-1 (GND) Power window motor UP input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
M4-10 (UP) - M4-1 (GND) Power window motor UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
M4-10 (UP) - M4-1 (GND) Power window motor UP input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
M4-10 (UP) - M4-1 (GND) Power window motor UP input Ignition switch ON, rear RH door power window fully closed 11 to 14 V



CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E434509C02
4.417,3.24 4.802,3.469 0.385,0.229 1.521,4.5 1.906,4.729 0.385,0.229 3.875,4.5 4.26,4.729 0.385,0.229 5.698,4.5 6.083,4.729 0.385,0.229 1.146,6.104 1.531,6.333 0.385,0.229 2.938,6.104 3.323,6.333 0.385,0.229 4.25,6.104 4.635,6.333 0.385,0.229 3.438,7.781 3.823,8.01 0.385,0.229 2.135,1.385 2.521,1.615 0.385,0.229 2.135,1.771 2.521,2 0.385,0.229 2.292,3.24 2.677,3.469 0.385,0.229 3.792,0.292 4.177,0.521 0.385,0.229 5.26,6.104 5.646,6.333 0.385,0.229 6.26,6.104 6.646,6.333 0.385,0.229 2.01,0.698 2.333,0.427 false 1.396,0.521 1.719,0.25 false 0.969,1.885 1.281,2.083 0.313,0.198 10 false 4H 1.167,2.385 1.479,2.583 0.313,0.198 10 false 4F 0.979,1.083 1.292,1.281 0.313,0.198 10 false 4E 0.979,1.594 1.292,1.792 0.313,0.198 10 false 4D 6.052,2.094 6.365,2.292 0.313,0.198 10 false 4A 2.229,1.438 2.688,1.635 0.458,0.198 10 false H5 2.229,1.813 2.688,2.01 0.458,0.198 10 false H4 3.896,0.333 4.281,0.521 0.385,0.188 10 false MB 2.417,3.292 2.885,3.5 0.469,0.208 10 false H4 4.531,3.292 4.99,3.49 0.458,0.198 10 false H5 3.052,6.146 3.51,6.344 0.458,0.198 10 false 4D 5.813,4.542 6.271,4.74 0.458,0.198 10 false 4A 3.542,7.813 4,8.01 0.458,0.198 10 false MB 2.385,0.354 2.698,0.552 0.313,0.198 10 false *2 6.031,1.729 6.344,1.927 0.313,0.198 10 false 4B 6.031,1.146 6.344,1.344 0.313,0.198 10 false 4C 0.969,2.146 1.281,2.344 0.313,0.198 10 false 4G 3.979,4.552 4.292,4.75 0.313,0.198 10 false 4B 1.635,4.542 1.948,4.74 0.313,0.198 10 false 4C 1.26,6.135 1.573,6.333 0.313,0.198 10 false 4E 4.365,6.146 4.677,6.344 0.313,0.198 10 false 4H 5.354,6.146 5.667,6.344 0.313,0.198 10 false 4G 6.375,6.146 6.688,6.344 0.313,0.198 10 false 4F 1.771,0.146 2.083,0.344 0.313,0.198 10 false *1
*1 POWER DISTRIBUTION BOX ASSEMBLY *2 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the power distribution box assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors connected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-13 (GND1) - Body ground Ground Always Below 1 Ω
MB-26 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
MB-27 (IGR) - Body ground IG power supply Ignition switch ON 11 to 14 V


d.

Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-4 (FRCY) - Body ground Front door courtesy light switch (for RH) input Front door RH open Below 1 V
MB-4 (FRCY) - Body ground Front door courtesy light switch (for RH) input Front door RH closed 11 to 14 V
H4-28 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
H4-28 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder not turned Pulse generation
H4-4 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
H4-4 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder not turned Pulse generation