The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B009583 | Right Frontal Restraints Sensor Value of Signal Protection Calculation Incorrect | ·
The airbag sensor assembly detects a line short in the front airbag sensor RH circuit for 2 seconds ·
The airbag sensor assembly detects a short to ground in the front airbag sensor RH circuit for 2 seconds ·
The airbag sensor assembly detects a short to B+ in the front airbag sensor RH circuit for 2 seconds ·
The airbag sensor assembly detects an open in the front airbag sensor RH circuit for 2 seconds ·
Front airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Harness or connector ·
Front airbag sensor RH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Procedure1
Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH.
The connectors are properly connected.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Front Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Front Airbag Sensor RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-2 (+SR) - A42-1 (-SR) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Front Airbag Sensor RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-2 (+SR) - Body ground | Always | 1 MΩ or higher |
| A42-1 (-SR) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Front Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Front Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Using a service wire, connect terminals 29 (+SR) and 28 (-SR) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-2 (+SR) - A42-1 (-SR) | Always | Below 1 Ω |
Post-procedure1
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | Front Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Front Airbag Sensor RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A42-2 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| A42-1 (-SR) - Body ground | Ignition switch ON | Below 1 V |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the airbag sensor assembly.
Interchange the front airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTCs B009083 and B009583 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| B009583 is output | A |
| B009083 is output | B |
| B009083 and B009583 are not output | C |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the front airbag sensor RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING