The side collision sensor LH circuit (bus 2) consists of the airbag sensor assembly and No. 1 side airbag sensor LH.
The No. 1 side airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B009283 | Left Side Restraints Sensor 2 Value of Signal Protection Calculation Incorrect | ·
The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 2) for 2 seconds ·
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 2) for 2 seconds ·
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 2) for 2 seconds ·
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 2) for 2 seconds ·
No. 1 side airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Harness or connector ·
No. 1 side airbag sensor LH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Procedure1
Check that the connectors are properly connected to the airbag sensor assembly and No. 1 side airbag sensor LH.
The connectors are properly connected.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | No. 1 Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
Disconnect the connectors from the airbag sensor assembly and No. 1 side airbag sensor LH.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O5-2 (BFL+) - O5-1 (BFL-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O5-2 (BFL+) - Body ground | Always | 1 MΩ or higher |
| O5-1 (BFL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | No. 1 Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Using a service wire, connect terminals 28 (BCL+) and 29 (BCL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O5-2 (BFL+) - O5-1 (BFL-) | Always | Below 1 Ω |
Post-procedure1
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *1 | No. 1 Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O5-2 (BFL+) - Body ground | Ignition switch ON | Below 1 V |
| O5-1 (BFL-) - Body ground | Ignition switch ON | Below 1 V |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the airbag sensor assembly.
Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTCs B009283 and B009783 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| B009283 is output | A |
| B009783 is output | B |
| B009283 and B009783 are not output | C |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Center Pillar)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING