The side airbag pressure sensor LH and side airbag pressure sensor RH detect impacts to the vehicle through changes in pressure inside the front doors caused by deformation of the outer side of the front doors and send signals to the airbag sensor assembly.
Based on the signals sent by the side airbag pressure sensors, the airbag sensor assembly determines if the airbags and pretensioners should be deployed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B166A62 | Right Side Restraints Sensor 5 / Left Side Restraints Sensor 5 Signal Compare Failure | The difference between the pressure detected by the side airbag pressure sensor LH and the side airbag pressure sensor RH exceeds a certain value a certain number of times | ·
Side airbag pressure sensor LH ·
Side airbag pressure sensor RH ·
Airbag sensor assembly |
Comes on | Does not apply to test/check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs in the table below are output | A |
| Any of the DTCs in the table below are output | B |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Side collision sensor circuit (bus 1) malfunction | Airbag system | B009383 | Left Side Restraints Sensor 3 Value of Signal Protection Calculation Incorrect |
| B009384 | Left Side Restraints Sensor 3 Signal Below Allowable Range | ||
| B009385 | Left Side Restraints Sensor 3 Signal Above Allowable Range | ||
| B009387 | Left Side Restraints Sensor 3 Missing Message | ||
| B009396 | Left Side Restraints Sensor 3 Component Internal Failure | ||
| B009883 | Right Side Restraints Sensor 3 Value of Signal Protection Calculation Incorrect | ||
| B009884 | Right Side Restraints Sensor 3 Signal Below Allowable Range | ||
| B009885 | Right Side Restraints Sensor 3 Signal Above Allowable Range | ||
| B009887 | Right Side Restraints Sensor 3 Missing Message | ||
| B009896 | Right Side Restraints Sensor 3 Component Internal Failure | ||
| B009B64 | Left Side Restraints Sensor 5 Signal Plausibility Failure | ||
| B009B83 | Left Side Restraints Sensor 5 Value of Signal Protection Calculation Incorrect | ||
| B009B84 | Left Side Restraints Sensor 5 Signal Below Allowable Range | ||
| B009B85 | Left Side Restraints Sensor 5 Signal Above Allowable Range | ||
| B009B87 | Left Side Restraints Sensor 5 Missing Message | ||
| B009B96 | Left Side Restraints Sensor 5 Component Internal Failure | ||
| B009E64 | Right Side Restraints Sensor 5 Signal Plausibility Failure | ||
| B009E83 | Right Side Restraints Sensor 5 Value of Signal Protection Calculation Incorrect | ||
| B009E84 | Right Side Restraints Sensor 5 Signal Below Allowable Range | ||
| B009E85 | Right Side Restraints Sensor 5 Signal Above Allowable Range | ||
| B009E87 | Right Side Restraints Sensor 5 Missing Message | ||
| B009E96 | Right Side Restraints Sensor 5 Component Internal Failure | ||
If DTCs in the table above are output, troubleshoot those DTCs first.
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Replace the side airbag pressure sensor LH with a new one or known good one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
When using a new part, since the side airbag pressure sensor RH and LH have the same part number, prepare either one.
Use the prepared side airbag pressure sensor to check the side airbag pressure sensor RH as well.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTC B166A62 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| B166A62 is not output | A |
| B166A62 is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Restore the side airbag pressure sensor LH that was replaced for testing to its original location.
A
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
B
Replace the side airbag pressure sensor RH with a new one or known good one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
When using a new part, since the side airbag pressure sensor LH and RH have the same part number, prepare either one.
Use the prepared side airbag pressure sensor to check the side airbag pressure sensor LH as well.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTC B166A62 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| B166A62 is not output | A |
| B166A62 is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Restore the side airbag pressure sensor RH that was replaced for testing to its original location.
A
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
B