Home › Power Source / Network › NETWORKING › CXPI COMMUNICATION SYSTEM › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0420499 CXPI COMMUNICATION SYSTEM U

NETWORKING  CXPI COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION

E434509C09
4.417,3.24 4.802,3.469 0.385,0.229 1.521,4.5 1.906,4.729 0.385,0.229 3.875,4.5 4.26,4.729 0.385,0.229 5.698,4.5 6.083,4.729 0.385,0.229 1.146,6.104 1.531,6.333 0.385,0.229 2.938,6.104 3.323,6.333 0.385,0.229 4.25,6.104 4.635,6.333 0.385,0.229 3.438,7.781 3.823,8.01 0.385,0.229 2.135,1.385 2.521,1.615 0.385,0.229 2.135,1.771 2.521,2 0.385,0.229 2.292,3.24 2.677,3.469 0.385,0.229 3.792,0.292 4.177,0.521 0.385,0.229 5.26,6.104 5.646,6.333 0.385,0.229 6.26,6.104 6.646,6.333 0.385,0.229 2.01,0.698 2.333,0.427 false 1.396,0.521 1.719,0.25 false 0.969,1.885 1.281,2.083 0.313,0.198 10 false 4H 1.167,2.385 1.479,2.583 0.313,0.198 10 false 4F 0.979,1.083 1.292,1.281 0.313,0.198 10 false 4E 0.979,1.594 1.292,1.792 0.313,0.198 10 false 4D 6.052,2.094 6.365,2.292 0.313,0.198 10 false 4A 2.229,1.438 2.688,1.635 0.458,0.198 10 false H5 2.229,1.813 2.688,2.01 0.458,0.198 10 false H4 3.896,0.333 4.281,0.521 0.385,0.188 10 false MB 2.417,3.292 2.885,3.5 0.469,0.208 10 false H4 4.531,3.292 4.99,3.49 0.458,0.198 10 false H5 3.052,6.146 3.51,6.344 0.458,0.198 10 false 4D 5.813,4.542 6.271,4.74 0.458,0.198 10 false 4A 3.542,7.813 4,8.01 0.458,0.198 10 false MB 2.385,0.354 2.698,0.552 0.313,0.198 10 false *2 6.031,1.729 6.344,1.927 0.313,0.198 10 false 4B 6.031,1.146 6.344,1.344 0.313,0.198 10 false 4C 0.969,2.146 1.281,2.344 0.313,0.198 10 false 4G 3.979,4.552 4.292,4.75 0.313,0.198 10 false 4B 1.635,4.542 1.948,4.74 0.313,0.198 10 false 4C 1.26,6.135 1.573,6.333 0.313,0.198 10 false 4E 4.365,6.146 4.677,6.344 0.313,0.198 10 false 4H 5.354,6.146 5.667,6.344 0.313,0.198 10 false 4G 6.375,6.146 6.688,6.344 0.313,0.198 10 false 4F 1.771,0.146 2.083,0.344 0.313,0.198 10 false *1
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)



b.

Reconnect the power distribution box assembly connectors.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-13 (GND1) - Body ground Ground Always Below 1 Ω
MB-26 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
MB-27 (IGR) - Body ground IG power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


d.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
4D-5 - Body ground CXPI communication line Ignition switch ON Pulse generation
4E-43 - Body ground Rear window defogger signal (output) rear window defogger switch off Below 1 V
rear window defogger switch on 11 to 14 V
4B-2 - Body ground*1 Mirror heater drive voltage (output) Ignition switch ON, rear defogger switch off Below 1 V
Ignition switch ON, rear defogger switch on 11 to 14 V
4C-10 - Body ground Power retract mirror motor drive voltage (output) Outer rear view mirror assembly moves to the retracted position. Below 1 V
Outer rear view mirror assembly not move. 11 to 14 V
4C-21 - Body ground Power retract mirror motor drive voltage (output) Outer rear view mirror assembly moves to the return position Below 1 V
Outer rear view mirror assembly not move 11 to 14 V
4C-24 - Body ground*2 Rear defogger switch signal (input) rear window defogger switch off Below 1 V
rear window defogger switch on 11 to 14 V

*1: w/ Mirror Heater

*2: for Manual Air Conditioning System




SEMICONDUCTOR POWER INTEGRATION ECU


E360199E20
2.51,0.125 2.917,0.365 0.406,0.24 3.823,0.125 4.229,0.365 0.406,0.24 2.573,0.156 2.927,0.354 0.354,0.198 10 false A85 3.896,0.156 4.302,0.365 0.406,0.208 10 false A86

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A85 and A86 semiconductor power integration ECU connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A85-1 (+B) - Body ground Auxiliary battery power supply Ignition switch off 8 to 14 V
A86-5 (-S) - Body ground Headlight ECU sub-assembly operation signal input Ignition switch off 6 V or higher
Ignition switch ON Below 1.7 V
A86-16 (GND2) - Body ground Ground Always Below 1 Ω
A86-20 (IG) - Body ground IG power supply Ignition switch off Below 1.5 V
Ignition switch ON 8 to 14 V
A86-24 (-S) - Body ground Headlight ECU sub-assembly operation signal input Ignition switch off 6 V or higher
Ignition switch ON Below 1.7 V
A86-26 (GND1) - Body ground Ground Always Below 1 Ω


e.

Reconnect the A85 and A86 semiconductor power integration ECU connectors.


f.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A86-8 (CXPI) - Body ground CXPI communication line Ignition switch ON Pulse generation
A86-1 (L) - Body ground Headlight ECU sub-assembly LH power supply Ignition switch off Below 3.0 V
Ignition switch ON 8 V or higher
A86-2 (L)- Body ground Headlight ECU sub-assembly RH power supply Ignition switch off Below 3.0 V
Ignition switch ON 8 V or higher
A86-17 (L) - Body ground Front fog light output Front fog light not illuminated Below 3.0 V
Front fog light illuminated 8 V or higher
A86-18 (L) - Body ground Front fog light output Front fog light not illuminated Below 3.0 V
Front fog light illuminated 8 V or higher