Home › Power Source / Network › NETWORKING › CXPI COMMUNICATION SYSTEM › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0420499 CXPI COMMUNICATION SYSTEM C

NETWORKING  CXPI COMMUNICATION SYSTEM  B235287  Power Integration No.1 System Missing Message  B235587  Power Distribution Box Missing Message  B235787  Wiper Module Missing Message  B235887  Smart LDM Left Missing Message  B235987  Smart LDM Right Missing Message  


DESCRIPTION

This DTC is stored when CXPI communication between the semiconductor power integration ECU, power distribution box assembly, windshield wiper relay assembly or light control LED ECU and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B235287 Power Integration No.1 System Missing Message No communication between semiconductor power integration ECU and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

Semiconductor power integration ECU

·

Harness or connector


B235587 Power Distribution Box Missing Message No communication between power distribution box assembly and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly


B235787 Wiper Module Missing Message No communication between windshield wiper relay assembly and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

Windshield wiper relay assembly

·

Harness or connector


B235887 Smart LDM Left Missing Message No communication between light control LED ECU LH and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

Light control LED ECU LH

·

Harness or connector


B235987 Smart LDM Right Missing Message No communication between light control LED ECU RH and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

Light control LED ECU RH

·

Harness or connector



WIRING DIAGRAM

C433514E02
0.01,0.427 1.542,0.958 1.531,0.531 10 false from Auxiliary Battery 1.969,0.625 3.302,0.906 1.333,0.281 10 false INP STD NO. 1-1 3.26,0.448 3.573,0.615 0.313,0.167 10 false 4G 3.271,0.938 3.583,1.104 0.313,0.167 10 false 4F 3.323,0.24 3.635,0.406 0.313,0.167 10 false 1 3.594,0.448 3.906,0.615 0.313,0.167 10 false +B1 3.313,0.708 3.625,0.875 0.313,0.167 10 false 1 3.323,1.198 3.635,1.365 0.313,0.167 10 false 1 3.281,1.688 3.594,1.854 0.313,0.167 10 false 23 3.281,2.167 3.594,2.333 0.313,0.167 10 false 11 3.271,2.635 3.583,2.802 0.313,0.167 10 false 17 3.281,3.604 3.594,3.771 0.313,0.167 10 false 22 3.292,4.865 3.604,5.031 0.313,0.167 10 false 5 5.792,3.563 6.104,3.729 0.313,0.167 10 false 41 5.792,4.042 6.104,4.208 0.313,0.167 10 false 44 5.802,4.521 6.115,4.688 0.313,0.167 10 false 36 5.802,5.021 6.115,5.188 0.313,0.167 10 false 25 3.271,1.417 3.583,1.583 0.313,0.167 10 false 4H 3.281,1.896 3.594,2.063 0.313,0.167 10 false 4D 3.271,2.375 3.583,2.542 0.313,0.167 10 false 4B 3.26,2.865 3.573,3.031 0.313,0.167 10 false 4C 3.24,3.813 3.552,3.979 0.313,0.167 10 false MB 3.26,5.083 3.573,5.25 0.313,0.167 10 false 4D 5.781,3.792 6.094,3.958 0.313,0.167 10 false 4C 5.781,4.271 6.094,4.438 0.313,0.167 10 false 4B 5.792,4.74 6.104,4.906 0.313,0.167 10 false 4B 5.792,5.25 6.104,5.417 0.313,0.167 10 false 4C 3.615,0.938 3.927,1.104 0.313,0.167 10 false +B2 3.604,1.406 3.917,1.573 0.313,0.167 10 false +B3 3.604,1.896 3.917,2.063 0.313,0.167 10 false +B4 3.615,2.365 3.927,2.531 0.313,0.167 10 false IGR 3.604,2.854 3.917,3.021 0.313,0.167 10 false IGP 3.604,3.823 4.01,3.979 0.406,0.156 10 false CXPI 3.625,5.083 3.938,5.25 0.313,0.167 10 false CXPI 5.208,3.771 5.677,3.927 0.469,0.156 10 false GND1 6,1.479 6.99,1.927 0.99,0.448 10 false to Each Load 2.75,3.802 3.125,3.969 0.375,0.167 10 false CXPI 5.188,4.729 5.656,4.885 0.469,0.156 10 false GND3 5.188,5.24 5.656,5.396 0.469,0.156 10 false GND4 5.188,4.26 5.656,4.417 0.469,0.156 10 false GND2 0.583,2.365 2.396,2.854 1.813,0.49 10 false from Certification ECU (Smart Key ECU Assembly)*2 0.417,2.844 2.396,3.448 1.979,0.604 10 false from Ignition or Starter Switch Assembly*1 or Certification ECU (Smart Key ECU Assembly)*2 1.719,4.344 3.375,4.792 1.656,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 0.427,5.802 3.417,6.073 2.99,0.271 10 false *1: w/o Entry and Start System 0.438,6.115 3.271,6.396 2.833,0.281 10 false *2: w/ Entry and Start System 0.781,6.5 3.104,6.698 2.323,0.198 10 false : CXPI Communication Line 3.563,5.979 5.677,6.229 2.115,0.25 10 false Power Distribution Box Assembly

C434175E01
5.698,0.885 7.063,1.219 1.365,0.333 10 false from IGP Relay 5.688,1.354 7.063,1.677 1.375,0.323 10 false from WIPER Relay 5.625,6.656 7.083,6.99 1.458,0.333 10 false from Auxiliary Battery 5.604,7.229 7.104,7.76 1.5,0.531 10 false from IGR-NO. 1 Relay 0.917,9.323 3.5,9.656 2.583,0.333 10 false : CXPI Communication Line 2.583,0.875 2.823,1.063 0.24,0.188 10 false 4 2.521,1.094 2.823,1.281 0.302,0.188 10 false A49 3.979,0.875 4.281,1.063 0.302,0.188 10 false A50 3.979,1.365 4.281,1.552 0.302,0.188 10 false A50 3.979,1.896 4.281,2.083 0.302,0.188 10 false A49 4.052,0.688 4.292,0.875 0.24,0.188 10 false 6 4.042,1.188 4.281,1.375 0.24,0.188 10 false 8 4.052,1.708 4.292,1.896 0.24,0.188 10 false 5 4.542,1.042 5.198,1.219 0.656,0.177 10 false WASHER 2.875,1.083 3.281,1.26 0.406,0.177 10 false MPX1 3.479,0.854 3.885,1.031 0.406,0.177 9 false IGWS 3.573,1.365 3.979,1.542 0.406,0.177 10 false +B 3.573,1.896 3.979,2.073 0.406,0.177 10 false ES 2.385,2.375 4.75,2.615 2.365,0.24 10 false Windshield Wiper Relay Assembly 2.656,3.146 2.896,3.333 0.24,0.188 10 false 1 3.948,2.979 4.188,3.167 0.24,0.188 10 false 2 3.948,3.354 4.188,3.542 0.24,0.188 10 false 5 2.875,3.302 3.281,3.479 0.406,0.177 10 false AT1 3.615,3.094 4.021,3.271 0.406,0.177 10 false LO 3.698,3.469 4.104,3.646 0.406,0.177 10 false E 5.042,3.073 6.729,3.635 1.688,0.563 10 false from Semiconductor Power Integration ECU 2.563,3.958 2.969,4.135 0.406,0.177 10 false A4 2.531,4.115 4.792,4.302 2.26,0.188 10 false Light Control LED ECU LH*1 2.531,5.698 2.938,5.875 0.406,0.177 10 false A5 2.51,5.865 4.771,6.052 2.26,0.188 10 false Light Control LED ECU RH*1 2.677,4.875 2.917,5.063 0.24,0.188 10 false 1 3.948,4.719 4.188,4.906 0.24,0.188 10 false 2 3.948,5.104 4.188,5.292 0.24,0.188 10 false 5 2.885,5.031 3.292,5.208 0.406,0.177 10 false AS1 3.625,4.833 4.031,5.01 0.406,0.177 10 false LO 3.698,5.219 4.104,5.396 0.406,0.177 10 false E 2.5,6.885 2.802,7.073 0.302,0.188 10 false A86 2.49,7.813 2.792,8 0.302,0.188 10 false A86 2.479,8.344 2.781,8.531 0.302,0.188 10 false A86 4.052,6.677 4.354,6.865 0.302,0.188 10 false A85 4.042,7.24 4.344,7.427 0.302,0.188 10 false A86 2.573,6.677 2.813,6.865 0.24,0.188 10 false 8 2.542,7.594 2.781,7.781 0.24,0.188 10 false 26 2.531,8.125 2.771,8.313 0.24,0.188 10 false 16 4.125,6.448 4.365,6.635 0.24,0.188 10 false 1 4.083,7.01 4.323,7.198 0.24,0.188 10 false 20 2.885,6.875 3.292,7.052 0.406,0.177 10 false CXPI 2.875,7.802 3.281,7.979 0.406,0.177 10 false GND1 3.698,6.667 4.104,6.844 0.406,0.177 10 false +B 3.729,7.219 4.135,7.396 0.406,0.177 10 false IG 4.479,6.854 5.698,7.146 1.219,0.292 10 false STD P/I NO. 1 4.208,8.302 5.531,8.615 1.323,0.313 10 false to Each Load 5.063,4.813 6.75,5.344 1.688,0.531 10 false from Semiconductor Power Integration ECU 2.313,8.781 4.938,9.188 2.625,0.406 10 false Semiconductor Power Integration ECU 2.875,8.344 3.281,8.521 0.406,0.177 10 false GND2 4.438,7.406 5.635,7.792 1.198,0.385 10 false ECU-IGR NO. 1 1.948,3.51 2.354,3.688 0.406,0.177 10 false *1 1.927,5.26 2.333,5.438 0.406,0.177 10 false *1 0.188,8.396 1.927,8.74 1.74,0.344 10 false *1: for LED Headlight

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Result
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B235287, B235587, B235787, B235887 and B235987 is output A
DTC B235287, B235787, B235887 and B235987 is output B
DTC B235587 is output C
DTC B235287 is output D
DTC B235787 is output E
DTC B235887 is output F
DTC B235987 is output G
DTC is not output H



A

3.CHECK POWER DISTRIBUTION BOX ASSEMBLY

B

4.CHECK POWER DISTRIBUTION BOX ASSEMBLY

C

6.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)

D

7.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)

E

9.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY AND BODY GROUND)

F

11.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU LH - BATTERY AND BODY GROUND)

G

13.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU RH - BATTERY AND BODY GROUND)

H

3.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Disconnect the 4D power distribution box assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance
Tester Connection Condition Specified Condition
MB-22 (CXPI) - 4D-5 Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

4.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Disconnect the 4D power distribution box assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-22 (CXPI) - 4D-5 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - SEMICONDUCTOR POWER INTEGRATION ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - SEMICONDUCTOR POWER INTEGRATION ECU)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the 4D power distribution box assembly connector.


c.

Disconnect the A49 windshield wiper relay assembly connector.


d.

Disconnect the A4 light control LED ECU LH connector.


e.

Disconnect the A5 light control LED ECU RH connector.


f.

Disconnect the A86 semiconductor power integration ECU connector.


g.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-5 - A86-8 (CXPI) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
4D-5 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the 4B and 4C power distribution box assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4C-41 (GND1) - Body ground Always Below 1 Ω
4B-44 (GND2) - Body ground Always Below 1 Ω
4B-36 (GND3) - Body ground Always Below 1 Ω
4C-25 (GND4) - Body ground Always Below 1 Ω



e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4G-1 (+B1) - Body ground Ignition switch off 11 to 14 V
4F-1 (+B2) - Body ground Ignition switch off 11 to 14 V
4H-1 (+B3) - Body ground Ignition switch off 11 to 14 V
4D-23 (+B4) - Body ground Ignition switch off 11 to 14 V
4B-11 (IGR) - Body ground Ignition switch ON 11 to 14 V
4C-17 (IGP) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the A86 semiconductor power integration ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-26 (GND1) - Body ground Always Below 1 Ω



e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A85-1 (+B) - Body ground Ignition switch ON 8 to 14 V
A86-20 (IG) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - POWER DISTRIBUTION BOX ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the 4D power distribution box assembly connector.


d.

Disconnect the A86 semiconductor power integration ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-8 (CXPI) - 4D-5 Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A86-8 (CXPI) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the A49 and A50 windshield wiper relay assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-5 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A50-6 (IGWS) - Body ground Ignition switch ON 11 to 14 V
A50-8 (+B) - Body ground Ignition switch ON or less than approximately 60 seconds after ignition switch turned off 11 to 14 V
Approximately 60 seconds or more after ignition switch turned off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the A49 windshield wiper relay assembly connector.


d.

Disconnect the 4D power distribution box assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-4 (MPX1) - 4D-5 Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A49-4 (MPX1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU LH - BATTERY AND BODY GROUND)
a.

Disconnect the A4 light control LED ECU LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-5 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-2 (LO) - Body ground Taillight on → off. 9.5 to 14 V → Below 1 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU LH - POWER DISTRIBUTION BOX ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU LH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the A4 light control LED ECU LH connector.


d.

Disconnect the 4D power distribution box assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1 (AT1) - 4D-5 Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A4-1 (AT1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU RH - BATTERY AND BODY GROUND)
a.

Disconnect the A5 light control LED ECU RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-5 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-2 (LO) - Body ground Taillight on → off 9.5 to 14 V → Below 1 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU RH - POWER DISTRIBUTION BOX ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU RH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the A5 light control LED ECU RH connector.


d.

Disconnect the 4D power distribution box assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-1 (AS1) - 4D-5 Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A5-1 (AS1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR