Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0420500 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E434509C08
4.417,3.24 4.802,3.469 0.385,0.229 1.521,4.5 1.906,4.729 0.385,0.229 3.875,4.5 4.26,4.729 0.385,0.229 5.698,4.5 6.083,4.729 0.385,0.229 1.146,6.104 1.531,6.333 0.385,0.229 2.938,6.104 3.323,6.333 0.385,0.229 4.25,6.104 4.635,6.333 0.385,0.229 3.438,7.781 3.823,8.01 0.385,0.229 2.135,1.385 2.521,1.615 0.385,0.229 2.135,1.771 2.521,2 0.385,0.229 2.292,3.24 2.677,3.469 0.385,0.229 3.792,0.292 4.177,0.521 0.385,0.229 5.26,6.104 5.646,6.333 0.385,0.229 6.26,6.104 6.646,6.333 0.385,0.229 2.01,0.698 2.333,0.427 false 1.396,0.521 1.719,0.25 false 0.969,1.885 1.281,2.083 0.313,0.198 10 false 4H 1.167,2.385 1.479,2.583 0.313,0.198 10 false 4F 0.979,1.083 1.292,1.281 0.313,0.198 10 false 4E 0.979,1.594 1.292,1.792 0.313,0.198 10 false 4D 6.052,2.094 6.365,2.292 0.313,0.198 10 false 4A 2.229,1.438 2.688,1.635 0.458,0.198 10 false H5 2.229,1.813 2.688,2.01 0.458,0.198 10 false H4 3.896,0.333 4.281,0.521 0.385,0.188 10 false MB 2.417,3.292 2.885,3.5 0.469,0.208 10 false H4 4.531,3.292 4.99,3.49 0.458,0.198 10 false H5 3.052,6.146 3.51,6.344 0.458,0.198 10 false 4D 5.813,4.542 6.271,4.74 0.458,0.198 10 false 4A 3.542,7.813 4,8.01 0.458,0.198 10 false MB 2.385,0.354 2.698,0.552 0.313,0.198 10 false *2 6.031,1.729 6.344,1.927 0.313,0.198 10 false 4B 6.031,1.146 6.344,1.344 0.313,0.198 10 false 4C 0.969,2.146 1.281,2.344 0.313,0.198 10 false 4G 3.979,4.552 4.292,4.75 0.313,0.198 10 false 4B 1.635,4.542 1.948,4.74 0.313,0.198 10 false 4C 1.26,6.135 1.573,6.333 0.313,0.198 10 false 4E 4.365,6.146 4.677,6.344 0.313,0.198 10 false 4H 5.354,6.146 5.667,6.344 0.313,0.198 10 false 4G 6.375,6.146 6.688,6.344 0.313,0.198 10 false 4F 1.771,0.146 2.083,0.344 0.313,0.198 10 false *1
*1 POWER DISTRIBUTION BOX ASSEMBLY *2 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Remove main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
MB-13 (GND1) - Body ground Ground Always Below 1 Ω
MB-26 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
MB-27 (IGR) - Body ground IGR power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Install main body ECU (multiplex network body ECU) connector.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
4E-17 - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


B464297E37
1.5,0.302 1.927,0.594 0.427,0.292 1.635,0.375 2.094,0.573 0.458,0.198 10 false K7

a.

Disconnect the K7 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
K7-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
K7-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the K7 front power window regulator motor assembly RH connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
K7-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


B464297E38
1.5,0.302 1.927,0.594 0.427,0.292 1.635,0.375 2.094,0.573 0.458,0.198 10 false L7

a.

Disconnect the L7 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
L7-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
L7-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the L7 front power window regulator motor assembly LH connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
L7-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


B464297E39
1.5,0.302 1.927,0.594 0.427,0.292 1.625,0.375 2.083,0.573 0.458,0.198 10 false M4

a.

Disconnect the M4 rear power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
M4-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
M4-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the M4 rear power window regulator motor assembly RH connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
M4-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


B464297E40
1.5,0.302 1.927,0.594 0.427,0.292 1.635,0.375 2.094,0.573 0.458,0.198 10 false N4

a.

Disconnect the N4 rear power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
N4-2 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
N4-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the N4 rear power window regulator motor assembly LH connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
N4-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


B131578E43
3.385,0.24 3.802,0.49 0.417,0.25 3.5,0.271 3.813,0.458 0.313,0.188 10 false K5

a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
K5-11 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
K5-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the K5 multiplex network master switch assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
K5-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


B574584E02
3.375,0.406 3.792,0.656 0.417,0.25 4.802,0.406 5.219,0.656 0.417,0.25 1.969,0.417 2.385,0.667 0.417,0.25 4.896,0.479 5.208,0.677 0.313,0.198 10 false H46 3.469,0.469 3.781,0.667 0.313,0.198 10 false O47 2.073,0.469 2.385,0.667 0.313,0.198 10 false H45

a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
H46-6 (+B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
H46-29 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
H46-8 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (w/ Entry and Start System)


B439652E02
3.417,0.313 3.833,0.563 0.417,0.25 3.5,0.344 3.813,0.542 0.313,0.198 10 false H71

a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
H71-7 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
H71-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
H71-5 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ID CODE BOX (IMMOBILISER CODE ECU) (for HV Model with Entry and Start System)


B463711E04
3.24,0.24 3.677,0.49 0.438,0.25 3.344,0.302 3.802,0.5 0.458,0.198 10 false H67

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
H67-5 (GND) - Body ground Ground Always Below 1 Ω
H67-1 (+B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the H67 ID code box (immobiliser code ECU) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
H67-2 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation