When installing the name plates, heat the vehicle body, back door outside garnish and name plates and front bumper assembly using a heat light.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
·
Back Door Outside Garnish ·
Name Plate |
20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body, back door outside garnish or name plate or front bumper assembly excessively.
75374
1.INSTALL SIDE PANEL EMBLEM
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and side panel emblem.
Remove the release paper from a new side panel emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
for LH Side:
Install the side panel emblem as shown in the illustration.
| *a | Reference Values | *b | End of R |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 227.4 mm (8.95 in.) | B | 161.5 mm (6.36 in.) |
| C | 29.2 mm (1.15 in.) | D | 148.6 mm (5.85 in.) |
for RH Side:
Install the side panel emblem as shown in the illustration.
| *a | Reference Values | *b | End of R |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 145.9 mm (5.74 in.) | B | 25.5 mm (1.00 in.) |
| C | 157.3 mm (6.19 in.) | D | 226.7 mm (8.93 in.) |
75442A
2.INSTALL NO. 2 BACK DOOR NAME PLATE
Clean the back door outside garnish surface.
Using a heat light, heat the back door outside garnish surface.
Remove any remaining double-sided tape from the back door outside garnish.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the back door outside garnish and a new No. 2 back door name plate.
Remove the release paper from the No. 2 back door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | location pin |
Engage the location pins and install the No. 2 back door name plate as shown in the illustration.
75441E
3.INSTALL NO. 1 BACK DOOR NAME PLATE
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and No. 1 back door name plate.
Remove the release paper from a new No. 1 back door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 1 back door name plate as shown in the illustration.
| *a | Reference Values | *b | Edge of Back Door Panel |
| *c | End of R | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 45.4 mm (1.787 in.) | B | 148.2 mm (5.835 in.) |
| C | 19.6 mm (0.772 in.) | D | 18.3 mm (0.720 in.) |
75435A
4.INSTALL BACK DOOR ORNAMENT
Install the back door ornament.
75741E
5.INSTALL SYMBOL EMBLEM
Engage the guide and claws to install the symbol emblem.