Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088302 EXTERIOR PANELS / TRIM _0421046 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75561 1.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:

When installing new No. 1 roof drip side finish moulding clips, remove any double-sided tape remaining where the No. 1 roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.


a.
B435994C01
2.198,0.396 2.51,0.396 false 0.75,0.583 1.594,1.021 true 1.969,0.313 2.281,0.469 0.313,0.156 10 false *a 0.563,0.469 0.875,0.625 0.313,0.156 10 false *b
*a Adhesive
*b 2 to 3 mm Bead of Adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new No. 1 roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



b.

Install the No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the No. 1 roof drip side finish moulding clips.

B577643C01
0.281,0.156 0.594,0.354 0.313,0.198 10 false *a 1.125,0.229 1.438,0.427 0.313,0.198 10 false A 2.344,0.323 2.656,0.521 0.313,0.198 10 false B 1.927,0.167 2.24,0.365 0.313,0.198 10 false *b 1.229,2.167 1.427,2.406 0.198,0.24 10 true *a 1.958,2.281 2.156,2.49 0.198,0.208 10 true *b 4.146,1.646 4.458,1.844 0.313,0.198 10 false *a 5.094,1.708 5.406,1.906 0.313,0.198 10 false C 5.875,1.656 6.188,1.854 0.313,0.198 10 false *b 6.26,1.76 6.573,1.958 0.313,0.198 10 false D 5.844,0.729 6.042,0.969 0.198,0.24 10 true *a 5.396,1.281 5.594,1.49 0.198,0.208 10 true *b
*a View A *b View B


Standard Measurement:
Area Measurement Area Measurement
A 1.5 to 2.5 mm (0.0591 to 0.0984 in.) B 4.0 mm (0.157 in.)
C 1.9 to 2.9 mm (0.0748 to 0.114 in.) D 4.0 mm (0.157 in.)



c.

Install the roof drip side finish moulding when 40 minutes or more have elapsed since the No. 1 roof drip side finish moulding clips were installed.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours




Hide 75552 2.INSTALL ROOF DRIP SIDE FINISH MOULDING

a.

Engage the clips to install the roof drip side finish moulding.


b.

Remove the protective tape.