Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P060694  Control Module Processor Unexpected Operation  


DESCRIPTION

The ECM calculates and compares the accelerator pedal opening angle value used for control and the value used for monitoring.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P060694 Control Module Processor Unexpected Operation Condition where output of the accelerator opening angle value used for control is more excessive than that of the accelerator opening angle value used for monitoring is continuously detected for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Wire harness or connector

·

ECM


Comes on DTC stored SAE: P0606

MONITOR DESCRIPTION

The ECM calculates the accelerator pedal opening angle value used for control and the value used for monitoring. If the ECM determines there is an excessive output while the engine is running, a DTC is stored and the MIL is illuminated.

MONITOR STRATEGY

Required Sensors/Components Accelerator pedal sensor assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the GTS off.

6.

Turn the ignition switch off.

7.

Disconnect the GTS.

8.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

9.

Connect the cable to the negative (-) battery terminal.

10.

Connect the GTS to the DLC3.

11.

Start the engine.

12.

Turn the GTS on.

13.

With the vehicle stopped, repeat the accelerator pedal operation (press the accelerator pedal from a state where it is not depressed) several times.

14.

Enter the following menus: Powertrain / Engine / Trouble Codes.

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P060694.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P060694)
2.READ OUTPUT DTC (DTC P060694)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


b.

Connect the cable to the negative (-) battery terminal.


c.

Start the engine.


d.

With the vehicle stopped, repeat the accelerator pedal operation (press the accelerator pedal from a state where it is not depressed) several times.


Procedure1

e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

f.

None.


Result:
Result Proceed to
DTCs are not output A
P060694 is output B



A

CHECK FOR INTERMITTENT PROBLEMS

B

3.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-6 (VPA) - A54-55 (VPA) Always Below 1 Ω
A62-3 (VPA2) - A54-58 (VPA2) Always Below 1 Ω
A62-4 (VCPA) - A54-57 (VCPA) Always Below 1 Ω
A62-1 (VCP2) - A54-60 (VCP2) Always Below 1 Ω
A62-5 (EPA) - A54-56 (EPA) Always Below 1 Ω
A62-2 (EPA2) - A54-59 (EPA2) Always Below 1 Ω
A62-6 (VPA) or A54-55 (VPA) - Body ground and other terminals Always 10 kΩ or higher
A62-3 (VPA2) or A54-58 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A62-4 (VCPA) or A54-57 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
A62-1 (VCP2) or A54-60 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
A62-5 (EPA) or A54-56 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A62-2 (EPA2) or A54-59 (EPA2) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR