Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P060609  Control Module Processor (Brake Override System Output Signal) Component Failure  


DESCRIPTION

The ECM calculates and compares the accelerator opening angle command value used for control and the value used for monitoring, after corrected by the brake override system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P060609 Control Module Processor (Brake Override System Output Signal) Component Failure Output of the accelerator opening command value after corrected by the brake override system used for control is more excessive than that of the accelerator opening angle command value after corrected by the brake override system repairs used for monitoring (1 trip detection logic). ECM Comes on DTC stored SAE: P0606

MONITOR DESCRIPTION

The ECM calculates and compares the accelerator opening angle command value used for control and the value used for monitoring, after corrected by the brake override system. If the ECM determines there is an excessive output when both the accelerator pedal and brake pedal are depressed in that order, a DTC is stored and the MIL is illuminated.

MONITOR STRATEGY

Required Sensors/Components
·

Accelerator pedal sensor assembly

·

Stop light switch assembly

·

Speed sensor


Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

All of the following conditions are met -
Accelerator opening angle 25° or more
STP signal ON
Vehicle speed 40 km/h or higher
Accelerator opening angle value No malfunction
STP No malfunction
Wheel speed No malfunction
IGP ON

CONFIRMATION DRIVING PATTERN

A330723E35
4.333,0.75 4.708,0.313 4.708,0.313 4.927,0.313 false 0.417,0.198 1.49,0.438 1.073,0.24 10 false Vehicle Speed 0.615,0.719 1.229,0.917 0.615,0.198 10 false 40 km/h 0.688,2.083 1.302,2.281 0.615,0.198 10 false Idling 0.104,2.365 1.396,2.552 1.292,0.188 10 false Ignition Switch ON 1.625,2.24 1.948,2.417 0.323,0.177 10 false [A] 4.979,0.25 5.302,0.427 0.323,0.177 10 false [B] 5.615,3.333 5.938,3.51 0.323,0.177 10 false [C]

CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving make absolutely sure that all road traffic laws, such as speed limits, are observed.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine.

9.

Drive the vehicle at 40 km/h or higher and operate the brake pedal with the accelerator pedal depressed 25° or more [B].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P060609.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P060609)

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Wait 1 second or more.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

d.

None.


Result:
Result Proceed to
DTCs are not output A
P060609 is output B



A

2.GO TO DTC CHART

B

2.GO TO DTC CHART
HINT:

After the inspection, Perform the following procedure.


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P060609 is output B



A

END

B