Home › Engine / Hybrid System › M15A-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD
RM36W0E _51 Engine / Hybrid System _088539 M15A-FKS INTAKE / EXHAUST _0421793 INTAKE MANIFOLD A

M15A-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL VACUUM HOSE

a.

Install the vacuum hose to the intake manifold.


Hide 17177 2.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.

Install a new No. 1 intake manifold to head gasket to the intake manifold.


Hide 17111 3.INSTALL INTAKE MANIFOLD

a.

w/ Stud Bolt:

i.
A463704

Temporarily install the intake manifold to the cylinder head sub-assembly.


ii.

Using an E8 "TORX" socket wrench, install the 2 stud bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


iii.
A463703N01
1.865,0.031 2.021,0.229 0.156,0.198 10 true 1 0.875,0.021 1.021,0.208 0.146,0.188 10 true 2 2.708,0.052 2.854,0.24 0.146,0.188 10 true 3 0.073,0.052 0.219,0.24 0.146,0.188 10 true 4 2.948,1.74 3.094,1.927 0.146,0.188 10 true 5

Temporarily install the 3 bolts and 2 nuts.


iv.

Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



b.

w/o Stud Bolt:

i.
A463705N01
2.948,1.719 3.073,1.885 0.125,0.167 10 true 5 0.083,0.073 0.208,0.24 0.125,0.167 10 true 4 2.677,0.031 2.802,0.198 0.125,0.167 10 true 3 0.875,0.01 1,0.177 0.125,0.167 10 true 2 1.854,0.042 1.979,0.208 0.125,0.167 10 true 1

Temporarily install the intake manifold to the cylinder head sub-assembly with the 5 bolts.


ii.

Tighten the 5 bolts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



Hide 82121 4.CONNECT ENGINE WIRE

a.
A463702

Engage the 5 clamps and connect the engine wire.


b.

Install the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 2 connectors.


Hide 89421 5.INSTALL E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 25601 6.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Install a new EGR inlet gasket to the intake manifold.


b.

Install a new EGR valve adapter gasket to the No. 1 EGR pipe sub-assembly.


c.

Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly to the intake manifold and EGR valve assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Engage the clamp to connect the engine wire.


e.

Connect the EGR valve assembly connector.


Hide 23826 7.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the intake manifold.


Hide 23820 8.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.

Engage the clamp to connect the fuel vapor feed hose assembly to the intake manifold.


Hide 25860 9.INSTALL PURGE VALVE (PURGE VSV)

Hide 22030 10.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY