The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends signals to the cooling fan ECU to regulate the cooling fan. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.
Inspect the fuses for circuits related to this system before performing the following procedure.
Make sure to perform the necessary procedures (adjustment, calibration, initialization, or registration) after parts related to the cooling fan system have been removed/installed or replaced.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan Duty Ratio.
| Tester Display |
|---|
| Control the Engine Cooling Fan Duty Ratio |
Check the operation of the cooling fan while operating it using the GTS.
| Tester Operation | Fan Operation |
|---|---|
| 30 - 100% | Cooling fan operates |
| 0% | Cooling fan stops |
| Result | Proceed to |
|---|---|
| OK | A |
| Cooling fan does not operate | B |
| Cooling fan does not stop | C |
A
B
C
Inspect the cooling fan motor.
Click hereEngine / Hybrid System>M15A-FKS (COOLING)>COOLING FAN MOTOR>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A48 cooling fan ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-1(+B1) - A48-3(E1) | Ignition switch ON | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A54 ECM connector.
Disconnect the A48 cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-32(RFC) or A48-2(SI) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A48 cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-3(E1) - Body ground | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN NO. 1 relay.
Click hereEngine / Hybrid System>M15A-FKS (COOLING)>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block |
| *2 | FAN NO. 1 Relay |
Remove the FAN NO. 1 relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (FAN NO. 1 relay) - Body ground | Always | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A48 cooling fan ECU connector.
Remove the FAN NO. 1 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-1(+B1) - 5 (FAN NO. 1 relay) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-1 (+B) or 5 (FAN NO. 1 relay) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the FAN NO. 1 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (FAN NO. 1 relay) - Body ground | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A54 ECM connector.
Disconnect the A48 cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-32(RFC) - A48-2(SI) | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the z1 cooling fan motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z1-1(-) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG