53876A
1.SEPARATE FRONT FENDER LINER LH
Remove the 2 screws and clip.
Separate the front fender liner LH.
2.DRAIN ENGINE COOLANT (for Engine)
When engine coolant is hot, do not remove the radiator cap sub-assembly or the radiator drain cock plug.
Fluid and steam may spray out due to high pressure, possibly resulting in burns.
| *1 | Radiator Cap Sub-assembly | *2 | Radiator Drain Cock Plug |
| *a | Hose |
Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.
Loosen the radiator drain cock plug.
Remove the radiator cap sub-assembly. Then drain the engine coolant.
| *1 | Radiator Cap Sub-assembly | *2 | Radiator Drain Cock Plug |
Collect the engine coolant in a container and dispose of it according to the regulations in your area.
Tighten the radiator drain cock plug by hand.
Disconnect the hose from the radiator drain cock.
3.ADD ENGINE COOLANT (for Engine)
| *a | Filler Tube End |
| *b | Engine Coolant Level |
| *c | 20 mm |
Slowly fill the radiator assembly with engine coolant from the radiator inlet opening. (Engine coolant level should be within 20 mm (0.787 in.) from the filler tube end.)
5.1 liters (5.4 US qts, 4.5 Imp. qts)
Do not substitute plain water for engine coolant.
TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
Remove the reserve tank cap.
| *a | F Line |
Slowly pour engine coolant into the radiator reserve tank until it reaches the F line.
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Set the engine in inspection mode.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Bleed air from the cooling system.
Before starting the engine, turn the A/C switch off.
Adjust the heater control to the maximum hot setting.
Adjust the blower speed to the low setting.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.
After the engine has warmed up, run the engine using the following cycle for at least 7 minutes: at 3000 rpm for 5 seconds, at idle speed for 45 seconds. (Repeat this cycle at least 8 times.)
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the system.
If the radiator reserve tank runs out of engine coolant just after the engine is started, stop the engine immediately, wait until the engine coolant has cooled down, and then add engine coolant.
If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
Make sure that the radiator reserve tank still has some engine coolant in it.
If there is not enough engine coolant, the engine may overheat or be seriously damaged.
If the radiator reserve tank does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant cools down, and 3) add engine coolant until the radiator reserve tank is filled to the F line.
| *a | F Line |
| *b | L Line |
After the engine has cooled down, check that the engine coolant level is between the F line and L line.
If the engine coolant level is below the L line, add engine coolant to the F line.
4.INSPECT FOR COOLANT LEAK (for Engine)
53876A
5.INSTALL FRONT FENDER LINER LH
Install the front fender liner LH.
nstall the 2 screws and clip.