Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › MOTOR CABLE
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0421989 MOTOR CABLE A

P910 HYBRID TRANSMISSION / TRANSAXLE  MOTOR CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cable removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
ECM Perform Vehicle Identification Number (VIN) registration DTC P063051 is output (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide G9200 1.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide G1148 2.REMOVE MOTOR CABLE

CAUTION:

Be sure to wear insulated gloves.


a.
C429079

Remove the 2 bolts and connector cover from the hybrid vehicle transaxle assembly.


b.
C429081

Disengage the 2 claws to remove the terminal cap from the hybrid vehicle transaxle assembly.


c.
C429083C01
0.906,3.24 1.219,3.052 true 0.719,3.156 0.958,3.365 0.24,0.208 10 false *a
*a Waterproof Seal


Using an insulated tool, remove the 6 bolts and motor cable from the hybrid vehicle transaxle assembly.

NOTICE:
·

Keep the motor cable terminals and their installation area free from foreign matter, water, etc.

·

Do not touch the waterproof seal or terminals of the motor cable.

·

Cover the hole where the motor cable was installed with tape or equivalent (non-residue type) to prevent entry of foreign matter.