Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE OIL SEAL › 2020.03–2020.07
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0421993 HYBRID TRANSAXLE OIL SEAL A

P910 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH or front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

PROCEDURE

Hide 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C429483N02
1.958,3.021 2.135,3.021 2.135,3.021 2.469,2.604 false 1.646,2.917 2.104,3.115 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal LH from the hybrid vehicle transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the hybrid vehicle transaxle assembly.



Hide 43410M 3.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C429484N02
1.01,2.74 1.479,2.74 false 1.552,2.646 1.948,2.833 0.396,0.188 10 false SST

Using SST, remove the front drive shaft oil seal RH from the hybrid vehicle transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the hybrid vehicle transaxle assembly.



Hide 43410M 4.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C429485C02
1.198,0.844 1.198,0.552 false 1.375,0.865 1.375,0.573 false 1.51,2.073 1.073,2.073 true 0.896,0.177 1.208,0.385 0.313,0.208 10 false *a 0.771,1.99 1.229,2.188 0.458,0.198 10 false SST 1.313,0.885 1.563,1.083 0.25,0.198 10 false *b 1.125,0.833 1.375,1.063 0.25,0.229 10 false *c
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install a new front drive shaft oil seal RH to the hybrid vehicle transaxle assembly.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the front drive shaft oil seal RH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal RH.

·

Do not install the front drive shaft oil seal RH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal RH.




Hide 43420H 5.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C429486C02
1.208,0.833 1.208,0.594 false 1.385,0.865 1.385,0.625 false 1.042,1.948 1.688,1.948 true 0.656,1.854 0.969,2.063 0.313,0.208 10 true SST 0.885,0.219 1.188,0.448 0.302,0.229 10 false *a 1.333,0.896 1.635,1.125 0.302,0.229 10 false *b 1.135,0.865 1.438,1.094 0.302,0.229 10 false *c
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install a new front drive shaft oil seal LH to the hybrid vehicle transaxle assembly.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the front drive shaft oil seal LH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal LH.

·

Do not install the front drive shaft oil seal LH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal LH.