Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0422043 BRAKE PEDAL(for HV Model) A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for HV Model)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal support assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When the steering sensor is replaced with a new one, ECU security key is necessary.

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of brake pedal support assembly
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Power steering ECU assembly Assist map writing
·

DTCs are stored

·

EPS warning light illuminates


(Click here)
ECU security key Vehicle control history (RoB) are stored (Click here)
Electric power steering column sub-assembly Assist map writing There is a difference in steering effort between turning left and right. (Click here)
Steering lock ECU (steering lock actuator or upper bracket assembly) Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.
Steering sensor (Including removal and installation)
·

Steering angle neutral point

·

Adjust steering angle setting


Parking assist monitor system (Click here)
ECU security key* Vehicle control history (RoB) are stored (Click here)

NOTICE:
·

When disassembling the Brake Pedal Support ASSY, do not loosen the breakaway bolt at the time of collisions.

·

If the breakaway bolt at the time of collisions is loosened, replace with a new Brake Pedal Support ASSY.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE STEERING COLUMN ASSEMBLY

Hide 89510D 2.REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY

Hide 84340 3.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 84345 4.REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

Hide 47101A 5.REMOVE BRAKE PEDAL RETURN SPRING

a.
C429617

Remove the brake pedal return spring from the brake pedal support assembly and push rod pin.


Hide 47264A 6.REMOVE PUSH ROD PIN

a.
C429619

Remove the clip and push rod pin to separate the brake pedal support assembly from the brake master cylinder push rod clevis.


Hide 47110 7.REMOVE BRAKE PEDAL SUPPORT ASSEMBLY

a.
C429623

Disengage the clamp to separate the wire harness from the brake pedal support assembly.


b.
C429621

Disengage the 3 clamps to separate the wire harness from the brake pedal support assembly.


c.
C429624

Remove the 2 clips.


d.

Remove the 2 nuts, 2 bolts and brake pedal support assembly.


Hide 47121 8.REMOVE BRAKE PEDAL PAD

a.

Remove the brake pedal pad from the brake pedal support assembly.