Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0422048 BRAKE BOOSTER PUMP A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Hide G9200 2.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 821H1 3.SEPARATE FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
C435061

Remove the bolt to separate the HV floor under wire from the vehicle body.


Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 44571A 5.SEPARATE NO. 1 BRAKE ACTUATOR HOSE

a.
C430251

Slide the clip and separate the No. 1 brake actuator hose from the No. 1 brake actuator tube.


Hide 473A1 6.SEPARATE ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C430253

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster pump assembly.


b.
C430254

Remove the bolt to separate the accumulator to brake master cylinder tube.


Hide 7.REMOVE BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.
C430256C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C430257C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.
C430259C01
1.042,1.469 1.313,1.021 true 2.135,1.646 2,1.375 true 2.573,0.885 2.26,0.99 true 2.333,0.385 2.031,0.844 true 1.656,0.167 1.792,0.719 true 1.229,0.344 1.531,0.615 true 0.938,1.479 1.177,1.688 0.24,0.208 10 true *a 2.042,1.656 2.281,1.854 0.24,0.198 10 true *b 2.594,0.781 2.854,0.99 0.26,0.208 10 true *c 2.281,0.167 2.5,0.365 0.219,0.198 10 true *d 1.573,0 1.76,0.198 0.188,0.198 10 true *e 1.042,0.26 1.271,0.49 0.229,0.229 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake lines.


d.
C430260

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


e.
C430261

Disengage the clamp to separate the brake line.


f.
C430263

Disconnect the connector.


g.

Disengage the clamp to separate the wire harness from the brake actuator bracket assembly.


h.
C430264

Disengage the clamp to separate the wire harness from the brake actuator bracket assembly.


i.
C430262

Remove the bolt, 2 nuts and brake actuator with brake booster pump assembly from the vehicle body.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:

Remove the brake actuator with brake booster pump assembly while avoiding the brake lines.



Hide 44571A 8.REMOVE NO. 1 BRAKE ACTUATOR HOSE

a.
C430266

Slide the clip and remove the No. 1 brake actuator hose from the brake booster pump assembly.


Hide 47381 9.REMOVE NO. 1 BRAKE TUBE CLAMP BRACKET

a.
C430268

Remove the bolt and No. 1 brake tube clamp bracket from the brake booster pump assembly.


Hide 47070 10.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C430270

Disengage the claw and clamp to separate the brake booster pump assembly wire harness from the brake actuator assembly bracket.


b.
C430271

Remove the nut from the brake booster pump assembly.


c.
C430272C01
0.625,4.115 0.958,4.115 false 0.563,3.688 0.896,3.688 false 1.677,4.073 2.083,3.5 2.083,3.5 2.25,3.5 true 2.531,4.219 2.74,3.885 2.74,3.885 2.906,3.885 true 0.438,4.052 0.75,4.25 0.313,0.198 10 false *1 0.365,3.625 0.677,3.823 0.313,0.198 10 false *2 2.292,3.427 2.604,3.625 0.313,0.198 10 false *3 2.938,3.823 3.25,4.021 0.313,0.198 10 false *4
*1 Union
*2 Connector
*3 Wire Harness
*4 Stud


Remove the brake booster pump assembly, brake booster pump bushing and brake actuator case collar from the brake actuator bracket assembly.

NOTICE:
·

Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.