Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › 2020.03–2020.09
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0422051 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  INSTALLATION  


PROCEDURE

Hide 89348S 1.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

If a rear center ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the rear bumper cover.

i.

Remove any remaining double-sided tape from the rear bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 20 mm (0.787 in.)


Cover the 2 sensor installation holes with a 20 mm (0.787 in.) circular piece of tape.


c.
E436518C01
2.969,1.135 2.656,1.135 true 2.979,1.042 3.229,1.302 0.25,0.26 10 true *a
*a Scribed Line
V100144

Primer Application


Apply primer to rear bumper assembly on the installation area of the rear center ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear center ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new rear center ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
E453623C01
2.969,1.135 2.656,1.135 true 2.469,0.854 2.833,0.542 2.833,0.542 2.469,0.563 true 2.979,1.042 3.229,1.302 0.25,0.26 10 true *a 2.823,0.427 3.052,0.625 0.229,0.198 10 true *b
*a Scribed Line
*b Identification Code


Check that the identification codes on the rear bumper assembly and the rear center ultrasonic sensor retainer are identical.


h.

Align the rear center ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the rear center ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89348R 2.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the rear bumper cover.

i.

Remove any remaining double-sided tape from the rear bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 20 mm (0.787 in.)


Cover the 2 sensor installation holes with a 20 mm (0.787 in.) circular piece of tape.


c.
E436518C01
2.969,1.135 2.656,1.135 true 2.979,1.042 3.229,1.302 0.25,0.26 10 true *a
*a Scribed Line
V100144

Primer Application


Apply primer to rear bumper assembly on the installation area of the rear corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear corner ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new rear corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
E453623C01
2.969,1.135 2.656,1.135 true 2.469,0.854 2.833,0.542 2.833,0.542 2.469,0.563 true 2.979,1.042 3.229,1.302 0.25,0.26 10 true *a 2.823,0.427 3.052,0.625 0.229,0.198 10 true *b
*a Scribed Line
*b Identification Code


Check that the identification codes on the rear bumper assembly and the rear corner ultrasonic sensor retainer are identical.


h.

Align the rear corner ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the rear corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89342A 3.INSTALL REAR CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E436521C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear center ultrasonic sensor.


b.

Connect the connector.


Hide 89342 4.INSTALL REAR CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E436522C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear corner ultrasonic sensor.


b.

Connect the connector.


Hide 5.INSTALL REAR BUMPER ASSEMBLY