Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE UNIT › 2020.03–2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422056 CONTINUOUSLY VARIABLE TRANSAXLE UNIT A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE UNIT  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Clean the work area, tools to be used, other equipment, etc., thoroughly before performing this procedure, as there is a possibility that a CVT malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, paper towels, etc., that may produce lint, dust or foreign matter.

·

When cleaning parts, make sure that dust or foreign matter does not enter the CVT.

·

When replacing any tapered roller bearing (inner race) or tapered roller bearing (outer race), replace both the tapered roller bearing (inner race) and tapered roller bearing (outer race) with new ones.

·

When the tapered roller bearing (inner race) is removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) need to be replaced.

·

When the tapered roller bearing (inner race) is not removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) can be reused.



HINT:

Shift shock may increase after replacing the transmission valve body assembly or forward multiple disc clutch assembly. In this case, shift shock will reduce as the vehicle is driven.


PROCEDURE

Hide 33493C 1.REMOVE TRANSMISSION OIL COOLER ASSEMBLY

a.
C432672

Remove the 3 bolts and transmission oil cooler from the transaxle housing.


b.
C432673

Remove the 2 O-rings from the transaxle housing.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C432674C01
1.167,1.406 1.552,1.406 true 0.958,1.313 1.156,1.542 0.198,0.229 10 true *a
*a Piece of Wood or Equivalent


Using a piece of wood or equivalent to secure the transmission control shaft lever to prevent it from rotating, remove the nut, washer and transmission control shaft lever from the manual valve lever shaft.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is not secured when loosening the nut, the manual valve link lever sub-assembly may separate from the manual valve.



b.
C432676

Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.


Hide 89419B 3.REMOVE SHIFT STROKE SENSOR

a.
C432677

Remove the bolt and shift stroke sensor from the transaxle case sub-assembly.


Hide 89413M 4.REMOVE TRANSMISSION REVOLUTION SENSOR (NOUT)

a.
C432678

Remove the bolt and transmission revolution sensor (NOUT) from the transaxle case sub-assembly.


b.
C395501

Remove the O-ring from the transmission revolution sensor (NOUT).


Hide 89413N 5.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)

a.
C432679

Remove the bolt and transmission revolution sensor (NT) from the rear transaxle case sub-assembly.


b.
C395501

Remove the O-ring from the transmission revolution sensor (NT).


Hide 89413T 6.REMOVE TRANSMISSION REVOLUTION SENSOR (NSS)

a.
C432680

Remove the bolt and transmission revolution sensor (NSS) from the transaxle case sub-assembly.


b.
C395501

Remove the O-ring from the transmission revolution sensor (NSS).


Hide 35151K 7.REMOVE AUTOMATIC TRANSMISSION CASE COVER

C432681

a.

Remove the 2 clips and automatic transmission case cover from the transaxle case sub-assembly.


Hide 89637K 8.REMOVE OIL PRESSURE SENSOR

a.
C432682

Remove the oil pressure sensor from the rear transaxle case sub-assembly.


Hide 9.REMOVE REFILL PLUG

a.
C432683

Remove the refill plug and gasket from the rear transaxle case sub-assembly.


Hide 30400 10.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.

Place the continuously variable transaxle assembly on wooden blocks.

C432684C01
2.896,1.281 2.698,0.948 2.698,0.948 2.958,1.167 false 3.344,1.5 3.583,1.5 false 2.531,0.854 2.802,1.073 0.271,0.219 10 false *a 3.625,1.396 3.896,1.615 0.271,0.219 10 false *a
*a Wooden Block - -



Hide 35125F 11.REMOVE OVERFLOW PLUG

a.
C432685

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle case sub-assembly.


Hide 35125E 12.REMOVE OVERFLOW(CVT) TUBE

a.
C432686

Using a 6 mm hexagon socket wrench, remove the overflow (CVT) tube from the transaxle case sub-assembly.


Hide 35015Y 13.REMOVE TRANSAXLE SIDE COVER SUB-ASSEMBLY

a.
C432687

Remove the 11 bolts and transaxle side cover sub-assembly from the transaxle case sub-assembly.


b.
C395511

Remove the O-ring from the transaxle side cover sub-assembly.


Hide 35410J 14.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C467183

Temporarily install the transmission control shaft lever to the manual valve lever shaft.


b.

Turn the transmission control shaft lever clockwise until it stops.


c.

Remove the transmission control shaft lever from the manual valve lever shaft.


d.
C432688

Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.


e.

Disconnect the 6 solenoid valve connectors.


f.
C432689

Remove the bolt and temperature sensor clamp from the transmission valve body assembly.


g.

Disconnect the temperature sensor from the transmission valve body assembly.


h.
C432690

Remove the 11 bolts and valve body assembly from the transaxle case sub-assembly.

NOTICE:

Make sure the manual valve does not fall out when removing the transmission valve body assembly, as the manual valve is not secured to the transmission valve body assembly.



i.
C432691

Remove the front oil pump cover gasket from the transaxle case sub-assembly.


j.
C432692

Remove the 3 transaxle case gaskets from the transaxle case sub-assembly.


Hide 82125M 15.REMOVE TRANSMISSION WIRE

a.
C432693

Disconnect the transmission revolution sensor (NC1) connector.


b.
C432694

Remove the bolt and transmission wire from the transaxle case sub-assembly.


c.
C395524

Remove the O-ring from the temperature sensor.


Hide 89413S 16.REMOVE TRANSMISSION REVOLUTION SENSOR (NC1)

a.
C432695

Remove the bolt and transmission revolution sensor (NC1) from the transaxle case sub-assembly.


Hide 35111C 17.REMOVE TRANSAXLE HOUSING

a.
C432696

Remove the 20 bolts.


b.

Using a plastic hammer, tap on the circumference of the transaxle housing to remove it from the transaxle case sub-assembly.


c.
C432697

Remove the 5 O-rings from the transaxle case sub-assembly.


Hide 35174B 18.REMOVE OIL RESERVOIR LOCK PLATE

a.
C432698

Remove the 3 bolts and oil reservoir lock plate from the transaxle housing.


Hide 35394D 19.REMOVE OIL CLEANER(CVT) MAGNET

a.
C432699

Remove the 3 oil cleaner magnets from the oil reservoir lock plate.


Hide 35882E 20.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C432700

Remove the 2 bolts and differential gear lube apply tube from the transaxle housing.


Hide 35896A 21.REMOVE SECONDARY SHAFT LUBE APPLY TUBE

a.
C432701

Using a snap ring plier, remove the snap ring from the transaxle housing.


b.
C432702

Remove the secondary shaft lube apply tube from the transaxle housing.


c.
C395535

Remove the O-ring from the secondary shaft lube apply tube.


Hide 35809 22.REMOVE C-2 CLUTCH PRESSURE APPLY TUBE SUB-ASSEMBLY

a.
C432703

Remove the C-2 clutch pressure apply tube sub-assembly from the transaxle housing.


b.
C395537

Remove the O-ring from the C-2 clutch pressure apply tube sub-assembly.


Hide 35593A 23.REMOVE CAM GUIDE SLEEVE

a.
C432705

Remove the 2 bolts and cam guide sleeve from the transaxle housing.


Hide 35556N 24.REMOVE PARKING LOCK PAWL SHAFT

a.
C432706C01
2.313,0.198 2.792,0.198 false 2.323,0.563 2.729,0.74 true 2.135,0.104 2.406,0.313 0.271,0.208 10 false *1 2.135,0.458 2.417,0.656 0.281,0.198 10 false *2
*1 Parking Lock Pawl Shaft
*2 Torsion Spring


Remove the parking lock pawl shaft and torsion spring from the transaxle housing.


Hide 35557C 25.REMOVE PARKING LOCK PAWL

a.
C432707

Remove the parking lock pawl from the transaxle housing.


Hide 35598B 26.REMOVE PARKING LOCK SLEEVE

a.
C432708

Remove the parking lock sleeve from the transaxle housing.


Hide 27.REMOVE REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)

a.
C432709N01
2.302,1.083 2.635,1.083 false 2.698,0.969 3.156,1.167 0.458,0.198 10 false SST

Using SST, remove the reduction driven gear front tapered roller bearing (outer race) and shim from the transaxle housing.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle housing.


HINT:
C432710

Align the claw of SST with the indentation of the transaxle housing when removing the parts.



Hide 28.REMOVE DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)

a.
C432711N01
2.583,0.375 2.917,0.375 false 2.958,0.292 3.313,0.49 0.354,0.198 10 false SST

Using SST, remove the differential case front tapered roller bearing (outer race) and shim from the transaxle housing.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle housing.


HINT:
C432712

Align the claw of SST with the indentation of the transaxle housing when removing the parts.



Hide 43410M 29.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C432713N01
1.208,1.542 0.76,1.625 0.76,1.625 1.323,1.219 true 0.438,1.542 0.76,1.76 0.323,0.219 10 false SST

Using SST and a hammer, remove the front drive shaft oil seal RH from the transaxle housing.

SST
09950-70010  (09951-07150)
09950-60011  (09951-00580)


Hide 30.REMOVE CVT TYPE T OIL SEAL

a.
C432714N01
0.979,1.563 0.406,0.917 0.406,0.917 1.052,1.313 true 0.104,0.833 0.479,1.052 0.375,0.219 10 false SST

Using SST and a hammer, remove the transaxle housing type T oil seal from the transaxle housing.

SST
09950-70010  (09951-07100)
09950-60011  (09951-00520)


Hide 31.REMOVE REDUCTION DRIVEN GEAR SUB-ASSEMBLY

a.
C432715

Remove the reduction driven gear sub-assembly from the transaxle case sub-assembly.


Hide 32.REMOVE DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C432716

Remove the differential case sub-assembly from the transaxle case sub-assembly.


Hide 35317A 33.REMOVE NO. 2 TRANSMISSION OIL PUMP SEPARATE PLATE

a.
C432717

Disengage the 4 claws to remove the No. 2 transmission oil pump separate plate from the No. 1 transmission oil pump separate plate.


Hide 35782P 34.REMOVE DRIVE SPROCKET

a.
C432718

Remove the thrust needle roller bearing from the drive sprocket.


b.
C432719C01
1.198,0.292 1.792,0.292 true 2.177,0.469 2.656,0.469 true 1.01,0.208 1.292,0.448 0.281,0.24 10 false *1 2.708,0.354 2.99,0.594 0.281,0.24 10 false *2
*1 Drive Sprocket
*2 Transmission Drive Chain


Remove the drive sprocket and transmission drive chain.


Hide 35783N 35.REMOVE DRIVEN SPROCKET

a.

Using a snap ring expander, remove the driven sprocket from the front oil pump assembly.

C432720


b.

Remove the snap ring from the front oil pump assembly.


Hide 35316A 36.REMOVE NO. 1 TRANSMISSION OIL PUMP SEPARATE PLATE

a.
C432721

Remove the 2 bolts and No. 1 transmission oil pump separate plate from the front oil pump assembly.


Hide 35310A 37.REMOVE FRONT OIL PUMP ASSEMBLY

a.
C432722

Remove the 4 bolts and front oil pump assembly from the transaxle case sub-assembly.


b.
C432723

Remove the front oil pump cover gasket from the transaxle case sub-assembly.


Hide 35330J 38.REMOVE OIL STRAINER ASSEMBLY

a.
C432724

Remove the 2 bolts and oil strainer assembly from the front oil pump assembly.


b.
C432725

Remove the O-ring from the oil strainer assembly.


Hide 35165B 39.REMOVE NO. 1 TRANSMISSION CASE PLATE

a.
C432726

Remove the 2 bolts and No. 1 transmission case plate from the transaxle case sub-assembly.


Hide 35370E 40.REMOVE STATOR SHAFT ASSEMBLY

a.
C432727

Remove the 7 bolts and stator shaft assembly from the transaxle case sub-assembly.


Hide 33032 41.REMOVE 1ST GEAR SUB-ASSEMBLY

a.
C432728

Remove the bolt to disconnect the No. 1 gear shift fork assembly from the No. 1 gear shift fork shaft.


b.
C432729

Remove the 1st gear sub-assembly with the No. 1 gear shift fork assembly from the No. 1 gear shift fork shaft.


Hide 33210A 42.REMOVE NO. 1 GEAR SHIFT FORK ASSEMBLY

a.

Move the No. 1 gear shift fork assembly as shown in the illustration.

C432730


b.
C432731

Remove the No. 1 gear shift fork assembly from the 1st gear sub-assembly.


Hide 43.REMOVE STAY

a.
C432732

Remove the bolt and stay from the No. 1 gear shift fork assembly.


Hide 35610A 44.REMOVE FORWARD MULTIPLE DISC CLUTCH ASSEMBLY

a.
C432733

Remove the forward multiple disc clutch assembly from the planetary gear assembly.


b.
C398094

Remove the thrust bearing race from the forward multiple disc clutch assembly.


Hide 45.REMOVE NO. 1 CLUTCH DISC

a.
C432734

Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the forward clutch drum sub-assembly.

NOTICE:

Be careful not to damage the forward clutch drum sub-assembly.



b.
C395731C01
3.146,1.292 3.292,1.292 3.292,1.292 3.292,2.792 false 2.021,2.156 1.833,2.156 1.833,2.156 1.833,1.021 false 1.625,1.021 2.031,1.021 false 1.833,1.583 2.021,1.583 false 3.167,1.885 3.292,1.885 false 3.156,2.49 3.292,2.49 false 1.625,0.698 2.031,0.698 false 1.469,0.604 1.771,0.823 0.302,0.219 10 false *1 1.469,0.927 1.76,1.156 0.292,0.229 10 false *2 3.229,2.792 3.417,3.01 0.188,0.219 10 false *3
*1 Clutch Flange
*2 No. 1 Clutch Disc
*3 No. 1 Clutch Plate


Remove the clutch flange, 3 No. 1 clutch discs and 3 No. 1 clutch plates from the forward clutch drum sub-assembly.


Hide 46.REMOVE NO. 1 CLUTCH BALANCER

a.
C395732N01
1.906,0.917 2.396,0.917 false 2.448,0.823 2.833,1.094 0.385,0.271 10 false SST

Place SST on the No. 1 clutch balancer and compress the forward clutch return spring sub-assembly with a press.

SST
09387-00020  

NOTICE:

Do not compress the forward clutch return spring sub-assembly excessively.



b.
C395733

Using a snap ring expander, remove the snap ring from the forward clutch drum sub-assembly.


c.
C395734

Remove the No. 1 clutch balancer from the forward clutch drum sub-assembly.


d.
C395735

Remove the D-ring from the No. 1 clutch balancer.


Hide 35603E 47.REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C395736

Remove the forward clutch return spring sub-assembly from the forward clutch drum sub-assembly.


Hide 48.REMOVE CLUTCH PISTON

a.
C395737

Install the forward clutch drum sub-assembly to the stator shaft assembly.


b.

Apply compressed air (approximately 250 kPa (2.5 kgf/cm2, 36 psi)) to the fluid hole of the stator shaft assembly to separate the clutch piston from the forward clutch drum sub-assembly.

C395738

NOTICE:

Be careful as fluid may spray when applying compressed air.



c.
C395739

Remove the clutch piston from the forward clutch drum sub-assembly.


d.
C395740C01
1.021,0.302 1.302,0.49 0.281,0.188 10 false *1 2.625,1.844 2.896,2.042 0.271,0.198 10 false *2
*1 O-Ring
*2 D-Ring


Remove the O-ring and D-ring from the clutch piston.


e.
C395737

Remove the forward clutch drum sub-assembly from the stator shaft assembly.


Hide 49.REMOVE CLUTCH DRUM OIL SEAL RING

a.
C395741

Remove the 2 clutch drum oil seal rings from the stator shaft assembly.

NOTICE:

Do not expand the clutch drum oil seal rings excessively.



Hide 35720M 50.REMOVE PLANETARY GEAR ASSEMBLY

a.
C432735

Remove the planetary gear assembly from the front planetary ring gear sub-assembly.


b.
C432736

Remove the thrust needle roller bearing from the planetary gear assembly.


Hide 35075D 51.REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY

a.
C432737

Remove the thrust needle roller bearing from the front planetary ring gear sub-assembly.


b.
C432738

Remove the front planetary ring gear sub-assembly from the transaxle case sub-assembly.


Hide 35726A 52.REMOVE PLANETARY RING GEAR THRUST WASHER

a.
C432739

Remove the planetary ring gear thrust washer from the transaxle case sub-assembly.


Hide 35681B 53.REMOVE NO. 1 BRAKE DISC

a.
C432740

Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.

NOTICE:

Be careful not to damage the transaxle case sub-assembly.



b.
C432741C01
3.135,1.167 3.302,1.167 3.302,1.167 3.302,2.729 false 3.135,1.635 3.302,1.635 false 3.135,2.115 3.302,2.115 false 2.073,0.917 2.073,1.917 2.073,1.917 2.25,1.917 false 2.25,0.917 1.906,0.917 false 2.25,1.417 2.073,1.417 false 1.938,0.583 2.271,0.583 false 2.24,2.406 2.052,2.406 false 1.74,0.5 1.917,0.708 0.177,0.208 10 true *1 1.74,0.813 1.906,1.031 0.167,0.219 10 true *2 3.208,2.729 3.396,2.969 0.188,0.24 10 false *3 1.875,2.323 2.094,2.594 0.219,0.271 10 false *4
*1 Brake Flange
*2 No. 1 Brake Disc
*3 No. 1 Brake Plate
*4 Brake Cushion Plate


Remove the brake flange, 3 No. 1 brake discs, 3 No. 1 brake plates and brake cushion plate from the transaxle case sub-assembly.


Hide 54.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C432742N01
1.771,1.198 2.385,0.833 true 2.417,0.74 2.74,0.927 0.323,0.188 10 true SST

Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.

SST
09223-56010  

NOTICE:

Do not compress the 1st and reverse brake return spring sub-assembly excessively.



b.
C432743

Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.

NOTICE:

Be careful not to damage the transaxle case sub-assembly.



c.
C432744

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.


Hide 35623L 55.REMOVE REVERSE BRAKE PISTON

a.

Apply compressed air (approximately 250 kPa (2.5 kgf/cm2, 36 psi)) to the fluid hole to disconnect the reverse brake piston from the transaxle case sub-assembly.

C432745

NOTICE:

Be careful as fluid may spray when applying compressed air.



b.
C432746

Remove the reverse brake piston from the transaxle case sub-assembly.


c.
C395759

Remove the 2 O-rings from the reverse brake piston.


Hide 56.REMOVE REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)

a.
C432747N01
0.708,1.354 1.219,1.354 false 0.344,1.281 0.802,1.479 0.458,0.198 10 false SST

Using SST, remove the reduction driven gear rear tapered roller bearing (outer race) from the transaxle case sub-assembly.

SST
09308-00010  

HINT:
C432748

Align the claw of SST with the indentation of the transaxle case sub-assembly when removing the parts.



Hide 57.REMOVE DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)

a.
C432749N01
2.125,1.208 2.583,1.208 false 2.646,1.104 3.104,1.375 0.458,0.271 10 false SST

Using SST, remove the differential case rear tapered roller bearing (outer race) from the transaxle case sub-assembly.

SST
09308-00010  

HINT:
C432750

Align the claw of SST with the indentation of the transaxle case sub-assembly when removing the parts.



Hide 43420H 58.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C432751N01
1.042,1.646 0.385,1.271 0.385,1.271 1.146,1.333 true 0.073,1.198 0.531,1.396 0.458,0.198 10 false SST

Using SST and a hammer, remove the front drive shaft oil seal LH from the transaxle case sub-assembly.

SST
09950-60011  (09951-00600)
09950-70010  (09951-07100)


Hide 59.REMOVE REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)

a.
C396245C01
2.792,2.25 2.958,2.104 2.958,2.104 2.708,2.198 false 1.615,1.906 2.333,1.344 2.333,1.344 1.823,1.26 false 0.24,0.823 0.49,1.083 0.25,0.26 10 false *a 2.406,0.677 2.677,0.927 0.271,0.25 10 false *b 2.99,2 3.333,2.198 0.344,0.198 10 false SST 2.385,1.24 2.729,1.438 0.344,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the reduction driven gear rear tapered roller bearing (inner race) from the reduction driven gear sub-assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60011  (09951-00250)

NOTICE:

Because SST is attached to the roller portion, there is a possibility that the roller portion could break and SST could come off before the reduction driven gear rear tapered roller bearing (inner race) comes off.



b.
C396246C01
1.604,1.906 2.365,1.438 2.365,1.438 1.823,1.271 false 2.771,2.26 2.948,2.083 2.948,2.083 2.688,2.219 false 0.229,0.823 0.458,1.063 0.229,0.24 10 false *a 2.396,0.677 2.667,0.927 0.271,0.25 10 false *b 2.417,1.333 2.813,1.531 0.396,0.198 10 false SST 2.99,1.979 3.385,2.177 0.396,0.198 10 false SST
*a Hold
*b Turn


If the roller portion breaks and SST comes off, reattach SST to the inner race in the position shown in the illustration, and continue removing the parts.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60011  (09951-00250)


Hide 60.REMOVE REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)

a.
C396248C01
0.771,1.521 0.531,1.875 0.531,1.875 1.438,1.573 true 0.271,0.615 0.531,0.844 0.26,0.229 10 false *a 2.938,0.479 3.219,0.719 0.281,0.24 10 false *b 0.219,1.802 0.594,2.01 0.375,0.208 10 false SST
*a Hold
*b Turn


Using SST, remove the reduction driven gear front tapered roller bearing (inner race) from the reduction driven gear sub-assembly.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60011  (09951-00210)


Hide 61.REMOVE DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)

a.
C432752C01
0.625,1.521 0.417,1.781 0.417,1.781 1.24,1.583 true 0.198,0.667 0.51,0.896 0.313,0.229 10 false *a 2.813,0.531 3.052,0.771 0.24,0.24 10 false *b 0.094,1.729 0.552,1.927 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the differential case rear tapered roller bearing (inner race) from the differential case sub-assembly.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60011  (09951-00400)


Hide 62.REMOVE DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)

a.
C432753C01
0.646,1.51 0.448,1.802 0.448,1.802 1.229,1.552 true 0.229,0.615 0.479,0.833 0.25,0.219 10 false *a 2.813,0.469 3.063,0.729 0.25,0.26 10 false *b 0.135,1.74 0.594,1.938 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the differential case front tapered roller bearing (inner race) from the differential case sub-assembly.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60011  (09951-00380)


Hide 63.REMOVE STRAIGHT PIN

a.
C432754

Remove the 2 straight pins from the transaxle case sub-assembly.