Clean the work area, tools to be used, other equipment, etc., thoroughly before performing this procedure, as there is a possibility that a CVT malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the CVT.
Do not use cotton work gloves, cloths, paper towels, etc., that may produce lint, dust or foreign matter.
When cleaning parts, make sure that dust or foreign matter does not enter the CVT.
When replacing any tapered roller bearing (inner race) or tapered roller bearing (outer race), replace both the tapered roller bearing (inner race) and tapered roller bearing (outer race) with new ones.
When the tapered roller bearing (inner race) is removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) need to be replaced.
When the tapered roller bearing (inner race) is not removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) can be reused.
Shift shock may increase after replacing the transmission valve body assembly or forward multiple disc clutch assembly. In this case, shift shock will reduce as the vehicle is driven.
1. BEARING POSITION
Check the position and installation direction of each bearing.
| Mark | Thrust Bearing Race Diameter Inside / Outside
mm (in.) |
Thrust Needle Roller Bearing Diameter Inside / Outside
mm (in.) |
|---|---|---|
| A | - | 47.75 (1.88) / 65.8 (2.59) |
| B | 26.38 (1.04) / 38.9 (1.53) | 24.9 (0.98) / 38.9 (1.53) |
| C | - | 29.7 (1.17) / 49.1 (1.93) |
2.INSTALL STRAIGHT PIN
Install the 2 straight pins to the transaxle case sub-assembly.
7.0 to 8.0 mm (0.276 to 0.315 in.)
3.INSTALL DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)
Using SST and a press, install a new differential case rear tapered roller bearing (inner race) to the differential case sub-assembly.
Do not damage the differential case rear tapered roller bearing (inner race) cage when installing the differential case rear tapered roller bearing (inner race).
Be sure to install the differential case rear tapered roller bearing (inner race) so that there is no clearance between the differential case rear tapered roller bearing (inner race) and the differential case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.
4.INSTALL DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)
Using SST and a press, install a new differential case front tapered roller bearing (inner race) to the differential case sub-assembly.
Do not damage the differential case front tapered roller bearing (inner race) cage when installing the differential case front tapered roller bearing (inner race).
Be sure to install the differential case front tapered roller bearing (inner race) so that there is no clearance between the differential case front tapered roller bearing (inner race) and the differential case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.
5.INSTALL DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)
Using SST and a hammer, install a new differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.
Be sure to install the differential case rear tapered roller bearing (outer race) so that there is no clearance between the differential case rear tapered roller bearing (outer race) and the transaxle case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.
6.INSTALL DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)
Install the shim to the transaxle housing.
Using SST and a hammer, install a new differential case front tapered roller bearing (outer race) to the transaxle housing.
Be sure to install the differential case front tapered roller bearing (outer race) so that there is no clearance between the differential case front tapered roller bearing (outer race), shim and the transaxle housing. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.
7.ADJUST DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD
Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.
Make sure that there is no Toyota Genuine CVT fluid FE on the contact surfaces.
Install the differential case sub-assembly to the transaxle case sub-assembly.
Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.
Using SST, turn the differential case sub-assembly right and left 2 or 3 times to settle the bearings.
Using SST and a torque wrench, measure the turning torque of the differential case tapered roller bearing while rotating SST at 10 rpm.
1.61 to 2.57 N*m (17 to 26 kgf*cm, 15 to 22 in.*lbf)
If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.
| Part Number | Thickness
mm (in.) |
|---|---|
| 90564-58002 | 1.76 (0.0693) |
| 90564-58003 | 1.79 (0.0705) |
| 90564-58004 | 1.82 (0.0717) |
| 90564-58005 | 1.85 (0.0728) |
| 90564-58006 | 1.88 (0.0740) |
| 90564-58007 | 1.91 (0.0752) |
| 90564-58008 | 1.94 (0.0764) |
| 90564-58009 | 1.97 (0.0776) |
| 90564-58010 | 2.00 (0.0787) |
| 90564-58011 | 2.03 (0.0799) |
| 90564-58012 | 2.06 (0.0811) |
| 90564-58013 | 2.09 (0.0823) |
| 90564-58014 | 2.12 (0.0835) |
| 90564-58015 | 2.15 (0.0846) |
| 90564-58016 | 2.18 (0.0858) |
| 90564-58017 | 2.21 (0.0870) |
| 90564-58018 | 2.24 (0.0882) |
| 90564-58019 | 2.27 (0.0894) |
| 90564-58020 | 2.30 (0.0906) |
| 90564-58021 | 2.33 (0.0917) |
Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.
Remove the differential case sub-assembly from the transaxle case sub-assembly.
8.INSTALL REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)
Using SST and a press, install a new reduction driven gear rear tapered roller bearing (inner race) to the reduction driven gear sub-assembly.
Do not damage the reduction driven gear rear tapered roller bearing (inner race) cage when installing the reduction driven gear rear tapered roller bearing (inner race).
Be sure to install the reduction driven gear rear tapered roller bearing (inner race) so that there is no clearance between the reduction driven gear rear tapered roller bearing (inner race) and the reduction driven gear sub-assembly. If there is any clearance, the turning torque of the reduction driven gear sub-assembly cannot be measured correctly.
9.INSTALL REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)
Using SST and a press, install a new reduction driven gear front tapered roller bearing (inner race) to the reduction driven gear sub-assembly.
Do not damage the reduction driven gear front tapered roller bearing (inner race) cage when installing the reduction driven gear front tapered roller bearing (inner race).
Be sure to install the reduction driven gear front tapered roller bearing (inner race) so that there is no clearance between the reduction driven gear front tapered roller bearing (inner race) and the reduction driven gear sub-assembly. If there is any clearance, the turning torque of the reduction driven gear sub-assembly cannot be measured correctly.
10.INSTALL REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)
Using SST and a hammer, install a new reduction driven gear rear tapered roller bearing (outer race) to the transaxle case sub-assembly.
Be sure to install the reduction driven gear rear tapered roller bearing (outer race) so that there is no clearance between the reduction driven gear rear tapered roller bearing (outer race) and the transaxle case sub-assembly. If there is any clearance, the turning torque of the reduction driven gear sub-assembly cannot be measured correctly.
11.INSTALL REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)
Install the shim to the transaxle housing.
Using SST and a hammer, install a new reduction driven gear front tapered roller bearing (outer race) to the transaxle housing.
Be sure to install the reduction driven gear front tapered roller bearing (outer race) so that there is no clearance between the reduction driven gear front tapered roller bearing (outer race), shim and the transaxle housing. If there is any clearance, the turning torque of the reduction driven gear sub-assembly cannot be measured correctly.
12.ADJUST REDUCTION DRIVEN GEAR TAPERED ROLLER BEARING PRELOAD
Turn the reduction drive gear assembly right and left 2 or 3 times to settle the bearings.
Install SST.
Set SST to the parking lock gear as shown in the illustration.
| *a | SST (Center Bolt) | - | - |
Do not tighten SST (center bolt) more than is necessary to hold SST in place or the parking lock gear or bearing may unseat.
| *a | SST (Center Bolt) |
Tighten SST (center bolt).
Torque: 0.5 N*m (5 kgf*cm, 4 in.*lbf)
Using a torque wrench, measure and note the turning torque (T1) of the reduction drive gear assembly while rotating SST at 10 rpm.
No specified range is provided for T1 as it is only used for calculating the total preload of the differential case sub-assembly and reduction driven gear sub-assembly.
Remove SST from the parking lock gear.
Install the differential case sub-assembly to the transaxle case sub-assembly.
Install the reduction driven gear sub-assembly to the transaxle case sub-assembly.
Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.
Using SST, turn the differential case sub-assembly right and left 2 or 3 times to settle the bearings.
Using a torque wrench, measure and note the turning torque (T2) of the differential case tapered roller bearing while rotating SST at 10 rpm.
Subtract T1 from T2 to calculate the total preload of the differential case sub-assembly and reduction driven gear sub-assembly.
Differential case tapered roller bearing preload + 2.63 to 4.88 N*m (27 to 49 kgf*cm, 2 to 3 ft.*lbf)
If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.
| Part Number | Thickness
mm (in.) |
Mark |
|---|---|---|
| 90564-44074 | 1.71 (0.0673) | E |
| 90564-44075 | 1.74 (0.0685) | F |
| 90564-44076 | 1.77 (0.0697) | G |
| 90564-44077 | 1.80 (0.0709) | H |
| 90564-44078 | 1.83 (0.0720) | J |
| 90564-44079 | 1.86 (0.0732) | K |
| 90564-44080 | 1.89 (0.0744) | L |
| 90564-44081 | 1.92 (0.0756) | M |
| 90564-44082 | 1.95 (0.0768) | N |
| 90564-44083 | 1.98 (0.0780) | P |
| 90564-44084 | 2.01 (0.0791) | Q |
| 90564-44085 | 2.04 (0.0803) | R |
| 90564-44086 | 2.07 (0.0815) | S |
| 90564-44087 | 2.10 (0.0827) | T |
| 90564-44088 | 2.13 (0.0839) | U |
| 90564-44089 | 2.16 (0.0850) | V |
| 90564-44090 | 2.19 (0.0862) | W |
| 90564-44091 | 2.22 (0.0874) | X |
| 90564-44092 | 2.25 (0.0886) | Y |
| 90564-44093 | 2.28 (0.0898) | - |
| 90564-44094 | 2.31 (0.0909) | - |
| 90564-44095 | 2.34 (0.0921) | - |
| 90564-44096 | 2.37 (0.0933) | - |
Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.
Remove the reduction driven gear sub-assembly from the transaxle case sub-assembly.
Remove the differential case sub-assembly from the transaxle case sub-assembly.
43420H
13.INSTALL FRONT DRIVE SHAFT OIL SEAL LH
Using SST and a hammer, install a new front drive shaft oil seal LH to the transaxle case sub-assembly.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Make sure that the front drive shaft oil seal LH is installed in the correct direction.
Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.
Do not damage the lip of the front drive shaft oil seal LH.
35623L
14.INSTALL REVERSE BRAKE PISTON
Coat 2 new O-rings with Toyota Genuine CVT fluid FE and install them to the reverse brake piston.
Ensure that the O-rings is not twisted.
Install the reverse brake piston to the transaxle case sub-assembly.
15.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Install the 1st and reverse brake return spring sub-assembly to the transaxle case sub-assembly.
Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.
Do not compress the 1st and reverse brake return spring sub-assembly excessively.
Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the transaxle case sub-assembly.
Be careful not to damage the transaxle case sub-assembly.
35681B
16.INSTALL NO. 1 BRAKE DISC
| *1 | Brake Flange |
| *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate |
| *4 | Brake Cushion Plate |
Install the brake flange, 3 No. 1 brake discs, 3 No. 1 brake plates and brake cushion plate to the transaxle case sub-assembly.
Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the transaxle case sub-assembly.
| *a | Snap ring opening within this area. | - | - |
Be careful not to damage the transaxle case sub-assembly.
35726A
17.INSTALL PLANETARY RING GEAR THRUST WASHER
Install the planetary ring gear thrust washer to the transaxle case sub-assembly.
35075D
18.INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY
Install the front planetary ring gear sub-assembly to the transaxle case sub-assembly.
Coat the thrust needle roller bearing with Toyota Genuine CVT fluid FE and install it to the front planetary ring gear sub-assembly.
35720M
19.INSTALL PLANETARY GEAR ASSEMBLY
Coat the thrust needle roller bearing with Toyota Genuine CVT fluid FE and install it to the planetary gear assembly.
Install the planetary gear assembly to the front planetary ring gear sub-assembly.
20.INSTALL CLUTCH PISTON
| *1 | O-Ring |
| *2 | D-Ring |
Coat a new O-ring and a new D-ring with Toyota Genuine CVT fluid FE and install them to the clutch piston.
Ensure that the O-ring and D-ring are not twisted.
Install the clutch piston to the forward clutch drum sub-assembly.
35603E
21.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY
Install the forward clutch return spring sub-assembly to the forward clutch drum sub-assembly.
22.INSTALL NO. 1 CLUTCH BALANCER
Coat a new D-ring with Toyota Genuine CVT fluid FE and install it to the No. 1 clutch balancer.
Ensure that the D-ring is not twisted.
Install the No. 1 clutch balancer to the forward clutch drum sub-assembly.
Place SST on the No. 1 clutch balancer and compress the forward clutch return spring sub-assembly with a press.
Do not compress the forward clutch return spring sub-assembly excessively.
Using a snap ring expander, install the snap ring to the forward clutch drum sub-assembly.
23.INSTALL NO. 1 CLUTCH DISC
| *1 | Clutch Flange |
| *2 | No. 1 Clutch Disc |
| *3 | No. 1 Clutch Plate |
Install the clutch flange, 3 No. 1 clutch discs and 3 No. 1 clutch plates to the forward clutch drum sub-assembly.
Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the forward clutch drum sub-assembly.
Be careful not to damage the forward clutch drum sub-assembly.
35610A
24.INSTALL FORWARD MULTIPLE DISC CLUTCH ASSEMBLY
Install the thrust bearing race to the forward multiple disc clutch assembly.
Install the forward multiple disc clutch assembly to the planetary gear assembly.
25.INSTALL STAY
Clean and degrease the bolt and installation hole in the No. 1 gear shift fork assembly.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the end of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
In order to ensure proper sealing of the bolt, apply adhesive to the bolt and install it within 10 minutes of adhesive application.
Install the stay to the No. 1 gear shift fork assembly with the bolt.
33210A
26.INSTALL NO. 1 GEAR SHIFT FORK ASSEMBLY
Install the No. 1 gear shift fork assembly to the 1st gear sub-assembly.
Move the No. 1 gear shift fork assembly as shown in the illustration.
33032
27.INSTALL 1ST GEAR SUB-ASSEMBLY
Clean and degrease the bolt and installation hole in the No. 1 gear shift fork shaft.
Install the 1st gear sub-assembly with the No. 1 gear shift fork assembly to the No. 1 gear shift fork shaft.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the end of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
In order to ensure proper sealing of the bolt, apply adhesive to the bolt and install it within 10 minutes of adhesive application.
Install the bolt to connect the No. 1 gear shift fork assembly to the No. 1 gear shift fork shaft.
28.INSTALL CLUTCH DRUM OIL SEAL RING
Install 2 new clutch drum oil seal rings to the stator shaft assembly.
Do not expand the gap of the clutch drum oil seal ring excessively.
35370E
29.INSTALL STATOR SHAFT ASSEMBLY
Install the stator shaft assembly to the transaxle case sub-assembly with the 7 bolts.
| Bolt (A) | Bolt (B) |
|---|---|
| 30 mm (1.18 in.) | 40 mm (1.57 in.) |
35165B
30.INSTALL NO. 1 TRANSMISSION CASE PLATE
Install the No. 1 transmission case plate to the transaxle case sub-assembly with the 2 bolts.
35330J
31.INSTALL OIL STRAINER ASSEMBLY
Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the oil strainer assembly.
Ensure that the O-ring is not twisted.
Install the oil strainer assembly to the front oil pump assembly with the 2 bolts.
35310A
32.INSTALL FRONT OIL PUMP ASSEMBLY
Coat a new front oil pump cover gasket with Toyota Genuine CVT fluid FE and install it to the transaxle case sub-assembly.
Install the front oil pump assembly to the transaxle case sub-assembly with the 4 bolts.
| Bolt (A) | Bolt (B) |
|---|---|
| 30 mm (1.18 in.) | 40 mm (1.57 in.) |
35316A
33.INSTALL NO. 1 TRANSMISSION OIL PUMP SEPARATE PLATE
Install the No. 1 transmission oil pump separate plate to the front oil pump assembly with the 2 bolts.
35783N
34.INSTALL DRIVEN SPROCKET
Install the snap ring to the front oil pump assembly.
Using a snap ring expander, install the driven sprocket to the front oil pump assembly.
35782P
35.INSTALL DRIVE SPROCKET
| *1 | Drive Sprocket |
| *2 | Transmission Drive Chain |
Install the drive sprocket and transmission drive chain.
Install the thrust needle roller bearing to the drive sprocket.
35317A
36.INSTALL NO. 2 TRANSMISSION OIL PUMP SEPARATE PLATE
Engage the 4 claws to install the No. 2 transmission oil pump separate plate to the No. 1 transmission oil pump separate plate.
37.INSTALL DIFFERENTIAL CASE SUB-ASSEMBLY
Install the differential case sub-assembly to the transaxle case sub-assembly.
38.INSTALL REDUCTION DRIVEN GEAR SUB-ASSEMBLY
Install the reduction driven gear sub-assembly to the transaxle case sub-assembly.
39.INSTALL CVT TYPE T OIL SEAL
Coat the lip of a new transaxle housing type T oil seal with a small amount of MP grease.
Using SST and a hammer, install the transaxle housing type T oil seal to the transaxle housing.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Make sure that the transaxle housing type T oil seal is installed in the correct direction.
43410M
40.INSTALL FRONT DRIVE SHAFT OIL SEAL RH
Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Make sure that the front drive shaft oil seal RH is installed in the correct direction.
Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.
Do not damage the lip of the front drive shaft oil seal RH.
35598B
41.INSTALL PARKING LOCK SLEEVE
Install the parking lock sleeve to the transaxle housing.
35557C
42.INSTALL PARKING LOCK PAWL
Install the parking lock pawl to the transaxle housing.
35556N
43.INSTALL PARKING LOCK PAWL SHAFT
| *1 | Parking Lock Pawl Shaft |
| *2 | Torsion Spring |
Install the parking lock pawl shaft and torsion spring to the transaxle housing.
35593A
44.INSTALL CAM GUIDE SLEEVE
Install the cam guide sleeve to the transaxle housing with the 2 bolts.
35809
45.INSTALL C-2 CLUTCH PRESSURE APPLY TUBE SUB-ASSEMBLY
Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the C-2 clutch pressure apply tube sub-assembly.
Ensure that the O-ring is not twisted.
Install the C-2 clutch pressure apply tube sub-assembly to the transaxle housing.
35896A
46.INSTALL SECONDARY SHAFT LUBE APPLY TUBE
Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the secondary shaft lube apply tube.
Ensure that the O-ring is not twisted.
Install the secondary shaft lube apply tube to the transaxle housing.
| *a | Protrusion | *b | Cutout |
Align the cutout of the transaxle housing with the protrusion of the secondary shaft lube apply tube.
Using a snap ring plier, install the snap ring to the transaxle housing.
35882E
47.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE
Install the differential gear lube apply tube to the transaxle housing with the 2 bolts.
35394D
48.INSTALL OIL CLEANER(CVT) MAGNET
Install the 3 oil cleaner magnets to the oil reservoir lock plate.
35174B
49.INSTALL OIL RESERVOIR LOCK PLATE
Install the oil reservoir lock plate to the transaxle housing with the 3 bolts.
35111C
50.INSTALL TRANSAXLE HOUSING
Clean and degrease the contact surfaces of the transaxle housing and transaxle case sub-assembly.
Make sure that there is no Toyota Genuine CVT fluid FE on the contact surfaces.
Clean and degrease the 20 bolts and installation holes of the transaxle case sub-assembly.
Coat 5 new O-rings with Toyota Genuine CVT fluid FE and install them to the transaxle case sub-assembly.
Ensure that the O-rings is not twisted.
|
Seal Packing Start and End Point Range |
Apply seal packing to the transaxle case sub-assembly.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
1.5 mm (0.0591 in.)
Make sure to overlap the start and end points of the seal packing.
Make sure that the start and end points of the seal packing are within the shaded area shown in the illustration.
Apply seal packing in a continuous line (width 1.5 mm (0.0591 in.)) along the sealing surface.
After applying seal packing, install the transaxle housing to the transaxle case sub-assembly within 3 minutes and tighten the bolts within 10 minutes.
Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.
89413S
51.INSTALL TRANSMISSION REVOLUTION SENSOR (NC1)
Install the transmission revolution sensor (NC1) to the transaxle case sub-assembly with the bolt.
82125M
52.INSTALL TRANSMISSION WIRE
Coat the O-ring of the transmission wire with Toyota Genuine CVT fluid FE.
If reusing the transmission wire, check that the O-ring is not damaged.
Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the temperature sensor.
Ensure that the O-ring is not twisted.
Install the transmission wire to the transaxle case sub-assembly with the bolt.
Connect the transmission revolution sensor (NC1) connector.
Securely align the wire harness with the cutout of the transaxle case sub-assembly.
35410J
53.INSTALL TRANSMISSION VALVE BODY ASSEMBLY
Temporarily install the transmission control shaft lever to the manual valve lever shaft.
Turn the transmission control shaft lever clockwise until it stops.
Remove the transmission control shaft lever from the manual valve lever shaft.
Coat 3 new transaxle case gaskets with Toyota Genuine CVT fluid FE and install them to the transaxle case sub-assembly.
Coat a new front oil pump cover gasket with Toyota Genuine CVT fluid FE and install it to the transaxle case sub-assembly.
Align the slit portion of the manual valve and the manual valve link lever sub-assembly as shown in the illustration, and temporarily install the transmission valve body assembly to the transaxle case sub-assembly with the 2 bolts.
| *1 | Manual Valve | *2 | Manual Valve Link Lever Sub-assembly |
40 mm (1.57 in.)
Temporarily install the 9 bolts.
| Bolt (A) | Bolt (B) |
|---|---|
| 40 mm (1.57 in.) | 55 mm (2.17 in.) |
Connect the temperature sensor to the transmission valve body assembly.
To prevent it from being pinched between the transmission valve body assembly and the transaxle side cover sub-assembly, do not let the transmission wire ride up over the area shown in the illustration.
|
Do not let transmission wire protrude into this area. | - | - |
Temporarily install the temperature sensor clamp to the transmission valve body assembly with the bolt.
55 mm (2.17 in.)
Fully tighten the 12 bolts.
Connect the 6 solenoid valve connectors.
Engage the clamp to connect the transmission wire to the solenoid lock plate.
35015Y
54.INSTALL TRANSAXLE SIDE COVER SUB-ASSEMBLY
|
Area to be cleaned |
Clean the transaxle side cover sub-assembly installation surface of the transaxle case sub-assembly.
Completely remove any oil or grease from the contact surface of the transaxle case sub-assembly.
Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transaxle side cover sub-assembly.
Ensure that the O-ring is not twisted.
Temporarily install a new transaxle side cover sub-assembly to the transaxle case sub-assembly with the 11 bolts.
Fully tighten the 11 bolts in the order shown in the illustration.
35125E
55.INSTALL OVERFLOW (CVT) TUBE
Using a 6 mm hexagon socket wrench, install the overflow (CVT) tube to the transaxle case sub-assembly.
35125G
56.INSTALL OVERFLOW PLUG
Coat a new gasket with Toyota Genuine CVT fluid FE and install it to the overflow plug.
Using a 10 mm hexagon socket wrench, install the overflow plug to the transaxle case sub-assembly.
57.INSTALL REFILL PLUG
Coat a new gasket with Toyota Genuine CVT fluid FE and install it to the refill plug .
Install the refill plug to the rear transaxle case sub-assembly.
89637K
58.INSTALL OIL PRESSURE SENSOR
Coat the O-ring of the oil pressure sensor with Toyota Genuine CVT fluid FE.
If reusing the oil pressure sensor, check that the O-ring is not damaged.
Using a 27 mm deep socket wrench, install the oil pressure sensor to the rear transaxle case sub-assembly.
Be careful not to damage the O-ring.
35151K
59.INSTALL AUTOMATIC TRANSMISSION CASE COVER
Install the automatic transmission case cover to the transaxle case sub-assembly with the 2 clips.
89413T
60.INSTALL TRANSMISSION REVOLUTION SENSOR (NSS)
Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NSS).
Ensure that the O-ring is not twisted.
Install the transmission revolution sensor (NSS) to the transaxle case sub-assembly with the bolt.
Be careful not to damage the O-ring.
89413N
61.INSTALL TRANSMISSION REVOLUTION SENSOR (NT)
Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NT).
Ensure that the O-ring is not twisted.
Install the transmission revolution sensor (NT) to the rear transaxle case sub-assembly with the bolt.
Be careful not to damage the O-ring.
89413M
62.INSTALL TRANSMISSION REVOLUTION SENSOR (NOUT)
Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NOUT).
Ensure that the O-ring is not twisted.
Install the transmission revolution sensor (NOUT) to the transaxle case sub-assembly with the bolt.
Be careful not to damage the O-ring.
89419B
63.INSTALL SHIFT STROKE SENSOR
Coat the O-ring of the shift stroke sensor with Toyota Genuine CVT fluid FE.
If reusing the shift stroke sensor, check that the O-ring is not damaged.
Install the shift stroke sensor to the transaxle case sub-assembly with the bolt.
Be careful not to damage the O-ring.
84540
64.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.
Temporarily install the transmission control shaft lever to the manual valve lever shaft.
| *a | N |
Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
| *1 | Transmission Control Shaft Lever |
| *2 | Manual Valve Link Lever Sub-assembly |
| *3 | Manual Valve |
If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.
Remove the transmission control shaft lever from the manual valve lever shaft.
| *a | Protrusion |
Align the protrusions of the park/neutral position switch assembly as shown in the illustration.
Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.
Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.
Be careful of the direction of the transmission control shaft lever.
33493C
65.INSTALL TRANSMISSION OIL COOLER ASSEMBLY
Coat 2 new O-rings with Toyota Genuine CVT fluid FE and install them to the transaxle housing.
Ensure that the O-rings are not twisted.
Install the transmission oil cooler to the transaxle housing with the 3 bolts.