Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL PUMP
RM36W0E _51 Engine / Hybrid System _088660 M15A-FKS FUEL _0422103 FUEL PUMP A

M15A-FKS FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A464863

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.
A464864

Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Be careful not to bend the arm of the fuel sender gauge assembly.

·

To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank assembly as shown in the illustration.


A461402C01
1.823,0.469 2.104,0.469 false 1.906,1.167 2.115,1.167 false 1.844,1.563 2.125,1.563 false 5.344,1.646 5.521,1.531 false 5.125,1.333 5.573,0.865 true 5.042,0.844 5.396,0.573 false 2.167,1.49 2.479,1.646 0.313,0.156 10 false *1 2.156,1.104 2.469,1.26 0.313,0.156 10 false *2 2.135,0.406 2.448,0.563 0.313,0.156 10 false *3 5.552,1.438 5.865,1.594 0.313,0.156 10 false *1 5.635,0.781 5.948,0.938 0.313,0.156 10 false *2 5.438,0.49 5.75,0.646 0.313,0.156 10 false *3
*1 Fuel Sender Gauge Assembly *2 Fuel Sub-tank Sub-assembly
*3 Fuel Suction Plate Sub-assembly - -




c.

Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.

A464865C01
1.708,0.604 1.49,0.802 true 4.344,0.625 4.688,1.177 4.688,1.177 3.458,0.781 true 4.729,1.094 4.906,1.281 0.177,0.188 10 true *a 1.302,0.698 1.49,0.865 0.188,0.167 10 true *b
*a Protrusion *b Notch



Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.
A464866C01
1.271,0.427 0.74,0.427 true 1.167,0.813 0.885,0.813 true 2.885,1.135 2.604,1.135 true 2.719,0.854 2.354,0.958 true 2.479,1.625 2.24,1.448 true 1.281,2.917 0.938,2.917 true 1.302,2.813 1.479,2.99 0.177,0.177 10 true *a 2.906,1.042 3.073,1.208 0.167,0.167 10 true *b 2.5,1.531 2.677,1.698 0.177,0.167 10 true *c 2.719,0.74 2.917,0.896 0.198,0.156 10 true *d 0.719,0.729 0.896,0.896 0.177,0.167 10 true *c 0.51,0.344 0.708,0.5 0.198,0.156 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A464867C01
2.698,2.229 2.563,2.156 true 1.604,0.74 1.292,0.74 true 2.281,1.542 1.823,1.802 true 2.021,0.948 1.563,1.208 true 2.25,1.135 1.792,1.396 true 1.552,3.74 1.271,3.927 true 0.729,3.781 0.479,3.781 true 1.573,3.656 1.75,3.813 0.177,0.156 10 true *a 0.302,3.688 0.49,3.854 0.188,0.167 10 true *b 1.125,0.646 1.344,0.885 0.219,0.24 10 false *c 2.271,1.031 2.51,1.25 0.24,0.219 10 true *d 2.708,2.177 2.875,2.354 0.167,0.177 10 true *e 2.323,1.448 2.542,1.646 0.219,0.198 10 true *f 2.031,0.844 2.24,1.052 0.208,0.208 10 true *g
*a Triangle Mark (Fuel Pump Gauge Retainer)
*b Triangle Mark (Fuel Tank Assembly)
*c SST (Handle)
*d SST (Plate)
*e SST (Claw)
*f SST (Bolt)
*g Extension Bar
V100135

Tighten
V100136

Front Side of Vehicle


Install SST (handle) and an extension bar to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010)


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Engage the claw to install the No. 1 fuel tube clamp.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint of fuel tank main tube sub-assembly onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A464868C01
4.333,0.917 5.417,1.708 1.083,0.792 5.5,0.917 6.583,1.708 1.083,0.792 1.677,1.073 1.969,1.073 true 0.865,1.292 1.156,1.292 true 5.021,0.469 4.802,0.698 false 5.677,0.365 6.021,0.365 false 5.563,0.531 6.042,0.531 true 5.563,0.458 5.865,0.458 5.865,0.458 5.865,0.531 true 4.979,1.198 5.135,1.198 false 6.063,1.24 6.219,1.24 false 5.917,1.219 6.177,1.052 true 4.813,1.281 5.073,1.5 true 4.604,0.646 4.917,0.802 0.313,0.156 10 false *1 0.646,1.219 0.885,1.375 0.24,0.156 10 true *2 2.01,1.01 2.229,1.177 0.219,0.167 10 true *3 6.063,0.458 6.375,0.615 0.313,0.156 10 false *b 4.375,0.938 4.688,1.094 0.313,0.156 10 false *c 5.552,0.938 5.865,1.094 0.313,0.156 10 false *d 6.208,0.979 6.521,1.135 0.313,0.156 10 false *a 6.052,0.292 6.292,0.448 0.24,0.156 10 true *2 5.177,1.135 5.385,1.313 0.208,0.177 10 true *2 6.25,1.177 6.49,1.333 0.24,0.156 10 true *2 5.115,1.438 5.427,1.594 0.313,0.156 10 false *a
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 77701W 4.CONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.

Connect the No. 1 canister outlet hose sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.


Hide 77027B 5.CONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Connect the No. 1 fuel emission tube sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.


Hide 58325E 6.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the 2 fuel suction tube with pump and gauge assembly connectors.


d.

Install the rear floor service hole cover with new butyl tape.

NOTICE:

Securely install the rear floor service hole cover.



Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 8. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 10.INSTALL REAR SEAT ASSEMBLY

Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION