Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL PUMP (for High Pressure)
RM36W0E _51 Engine / Hybrid System _088660 M15A-FKS FUEL _0422104 FUEL PUMP(for High Pressure) A

M15A-FKS FUEL  FUEL PUMP(for High Pressure)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 23100X 1.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY

NOTICE:

When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A464881C01
2.01,1.052 2.49,0.677 true 1.281,2.521 1.448,2.521 false 1.229,3.094 1.396,3.094 false 1.333,4.042 1.5,4.042 false 2.875,2.521 3.042,2.521 false 2.802,2.969 2.969,2.969 false 2.958,4.021 3.125,4.021 false 1.458,2.406 1.667,2.573 0.208,0.167 10 false *1 1.385,3 1.573,3.177 0.188,0.177 10 false *2 2.5,0.573 2.698,0.74 0.198,0.167 10 true *3 0.865,2.313 1.177,2.469 0.313,0.156 10 false *a 2.448,2.292 2.76,2.448 0.313,0.156 10 false *b 3.052,2.417 3.26,2.583 0.208,0.167 10 false *1 2.99,2.865 3.177,3.042 0.188,0.177 10 false *2 1.51,3.927 1.708,4.094 0.198,0.167 10 true *3 3.156,3.917 3.354,4.083 0.198,0.167 10 true *3
*1 Fuel Pump Assembly
*2 Fuel Pump Lifter Assembly
*3 No. 2 Camshaft
*a Correct
*b Incorrect


Turn the crankshaft pulley until the flat of the No. 2 camshaft faces the fuel pump lifter assembly.

HINT:

This prevents the No. 2 camshaft nose from pushing up the fuel pump lifter assembly when installing the fuel pump assembly.



b.
A464882C01
1.313,1.552 1.313,2.219 true 1.958,1.115 2.354,0.833 true 1.031,4.417 1.427,4.135 true 1.271,2.25 1.583,2.406 0.313,0.156 10 false *1 2.406,0.74 2.573,0.896 0.167,0.156 10 true *a 0.833,4.313 1.146,4.469 0.313,0.156 10 false *b
*1 Fuel Pump Spacer Gasket
*a Pump Drive Cam (Engine Oil Application Area)
*b Fuel Pump Lifter Assembly (Engine Oil Application Area)


Apply 30 cc (1.8 cu. in.) of engine oil to the pump drive cam.


c.

Apply engine oil to the fuel pump lifter assembly.


d.

Install a new fuel pump spacer gasket to the cylinder head cover sub-assembly.


e.
A464883C01
1.906,2.792 2.375,2.385 true 1.948,1.729 2.177,1.729 true 1.104,2.26 1.563,2.698 true 1.229,1.635 1.458,1.635 true 1.031,1.552 1.219,1.74 0.188,0.188 10 true *a 0.927,2.167 1.104,2.344 0.177,0.177 10 true *b 2.188,1.615 2.375,1.792 0.188,0.177 10 true *c 2.385,2.271 2.573,2.458 0.188,0.188 10 true *d
*a Fuel Pump Lifter Assembly (Engine Oil Application Area)
*b Fuel Pump Lifter Guide (Engine Oil Application Area)
*c Stopper Key
*d Key Groove


Apply engine oil to the inside of the fuel pump lifter guide and the outside of the fuel pump lifter assembly.


f.

Set the fuel pump lifter assembly on the fuel pump lifter guide as shown in the illustration.

HINT:

Align the stopper key of the fuel pump lifter assembly with the key groove of the fuel pump lifter guide.



g.
A464884

Apply engine oil to a new O-ring and install it to the fuel pump assembly.

NOTICE:

Do not damage the O-ring.



h.
A464885

Set the fuel pump flange and fuel pump assembly on the cylinder head cover sub-assembly as shown in the illustration.


i.
A464886

Temporarily install the fuel pump assembly with the 2 bolts, leaving some allowance for left and right movement.


Hide 23801P 2.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

NOTICE:

Do not damage the seals of the union nuts of the No. 1 fuel pipe sub-assembly.


a.

Temporarily install the bolt.


b.

Temporarily install the No. 1 fuel pipe sub-assembly to the fuel delivery pipe and tighten the union nut by hand.


c.

Temporarily install the No. 1 fuel pipe sub-assembly to the fuel pump assembly and tighten the union nut by hand.


Hide 23100X 3.INSTALL FUEL PUMP ASSEMBLY

a.

Tighten the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


b.

Connect the fuel pump assembly connector.


Hide 23801P 4.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.

Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

A464887C01
5.844,0.958 6.104,0.76 false 6.115,0.646 6.292,0.854 0.177,0.208 10 false *a 4.917,0.615 5.229,0.771 0.313,0.156 10 false *b
*a 17 mm Union Nut Wrench *b Torque Wrench Fulcrum Length


Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




c.

Using an 8 mm socket wrench, tighten the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the ignition coil assembly connector.


Hide 23902 5.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel pump assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 44771 6.INSTALL VACUUM TUBE CONNECTOR HOSE

a.

Connect the vacuum tube connector hose to the vacuum pump assembly, and slide the clamp to secure the tube.


Hide 17881 7.INSTALL NO. 1 AIR CLEANER HOSE

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 9. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION