The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the map light assembly and telephone microphone assembly, and the map light assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.
Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-25 (SNS2) - V7-13 (SNS2) | Always | Below 1 Ω |
| H80-23 (MACC) - V7-16 (MACC) | Always | Below 1 Ω |
| H80-21 (MIN+) - V7-15 (MCO+) | Always | Below 1 Ω |
| H80-22 (MIN-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-23 (MACC) or V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| H80-21 (MIN+) or V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H80-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V7 map light assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H80-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-24 (SGND) - Body ground | Always | Below 1 Ω |
| H80-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V7 map light assembly connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Map Light Assembly) |
Connect an oscilloscope to terminals 15 (MCO+) and 14 (MCO-) of the V7 map light assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V7-15 (MCO+) - V7-14 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-13 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V7-16 (MACC) - MC-5 (MACC) | Always | Below 1 Ω |
| V7-15 (MCO+) - MC-3 (MIC+) | Always | Below 1 Ω |
| V7-14 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG