Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM36W0E _56 Audio / Visual / Telematics _088616 NAVIGATION / MULTI INFO DISPLAY _0422142 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter  


DESCRIPTION

The navigation ECU receives a vehicle speed signal from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E365516E83
1.563,0.344 2.708,0.604 1.146,0.26 10 false to Other Systems 2.135,1.479 2.448,1.677 0.313,0.198 10 false +S 2.427,1.396 2.74,1.594 0.313,0.198 10 false 36 4.625,1.406 4.938,1.604 0.313,0.198 10 false 9 4.813,1.479 5.26,1.698 0.448,0.219 10 false SPD 4.781,2.156 5.26,2.365 0.479,0.208 10 false H82 4.781,2.302 5.875,2.677 1.094,0.375 10 false Navigation ECU 1.25,2.156 2.021,2.354 0.771,0.198 10 false H6 1.24,2.302 3.208,2.656 1.969,0.354 10 false Combination Meter Assembly

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E396774C35
1.448,0.188 1.948,0.5 0.5,0.313 0.698,2.052 1.083,1.521 true 0.573,2.063 0.885,2.26 0.313,0.198 10 false +S 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.604,0.26 1.917,0.458 0.313,0.198 10 false H6 2.802,3.604 3.26,3.802 0.458,0.198 10 false GND 1.125,3.875 1.344,4.094 0.219,0.219 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal H6-36 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H6-36 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the H82 navigation ECU connector.


b.

Disconnect the H6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H82-9 (SPD) - H6-36 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR