Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2020.03–2020.07
RM36W0E _56 Audio / Visual / Telematics _088616 NAVIGATION / MULTI INFO DISPLAY _0422142 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly and telephone microphone assembly, and the map light assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E437737E01
0.969,0.708 1.583,0.906 0.615,0.198 10 false SNS2 0.938,1.156 1.552,1.354 0.615,0.198 10 false MACC 0.99,1.573 1.604,1.771 0.615,0.198 10 false MIC+ 1.021,2.031 1.635,2.229 0.615,0.198 10 false MIC- 0.333,2.417 0.948,2.615 0.615,0.198 10 false MC 0.344,2.573 1.729,3.01 1.385,0.438 10 false Telephone Microphone Assembly 0.219,3.677 0.833,3.875 0.615,0.198 10 false V7 0.208,3.833 1.99,4.208 1.781,0.375 10 false Map Light Assembly 1.438,0.615 2.052,0.813 0.615,0.198 10 false 1 1.438,1.073 2.052,1.271 0.615,0.198 10 false 5 1.438,1.49 2.052,1.688 0.615,0.198 10 false 3 1.438,1.948 2.052,2.146 0.615,0.198 10 false 2 1.927,0.604 2.427,0.802 0.5,0.198 10 false SNS2 1.906,1.052 2.406,1.25 0.5,0.198 10 false MACC 1.906,1.5 2.406,1.698 0.5,0.198 10 false MCO+ 1.927,1.948 2.427,2.146 0.5,0.198 10 false MCO- 2.385,0.615 3,0.813 0.615,0.198 10 false 13 2.385,1.063 3,1.26 0.615,0.198 10 false 16 2.385,1.5 3,1.698 0.615,0.198 10 false 15 2.375,1.948 2.99,2.146 0.615,0.198 10 false 14 3.656,2.448 4.271,2.646 0.615,0.198 10 false * 5.677,0.698 6.177,0.896 0.5,0.198 10 false SNS2 5.677,1.146 6.177,1.344 0.5,0.198 10 false MACC 5.677,1.583 6.177,1.781 0.5,0.198 10 false MIN+ 5.688,2.052 6.188,2.25 0.5,0.198 10 false MIN- 5.667,2.542 6.167,2.74 0.5,0.198 10 false SGND 5.302,0.719 5.802,0.917 0.5,0.198 10 false H80 5.292,1.167 5.792,1.365 0.5,0.198 10 false H80 5.302,1.573 5.802,1.771 0.5,0.198 10 false H80 5.313,2.042 5.813,2.24 0.5,0.198 10 false H80 5.313,2.542 5.813,2.74 0.5,0.198 10 false H80 5.333,0.5 5.948,0.698 0.615,0.198 10 false 25 5.333,0.969 5.948,1.167 0.615,0.198 10 false 23 5.333,1.406 5.948,1.604 0.615,0.198 10 false 21 5.344,1.854 5.958,2.052 0.615,0.198 10 false 22 5.354,2.354 5.969,2.552 0.615,0.198 10 false 24 5.354,4.51 5.969,4.708 0.615,0.198 10 false 25 5.333,5.281 5.948,5.479 0.615,0.198 10 false 26 5.323,5.99 5.938,6.188 0.615,0.198 10 false 24 5.292,4.698 5.792,4.896 0.5,0.198 10 false H81 5.323,5.458 5.823,5.656 0.5,0.198 10 false H81 5.302,6.167 5.802,6.365 0.5,0.198 10 false H81 5.667,4.688 6.167,4.885 0.5,0.198 10 false MCO+ 5.667,6.177 6.167,6.375 0.5,0.198 10 false SGND 5.677,5.469 6.177,5.667 0.5,0.198 10 false MCO- 5.656,6.667 6.875,7.177 1.219,0.51 10 false Radio and Display Receiver Assembly 4.698,5.698 5.313,5.896 0.615,0.198 10 false * 4.156,4.604 4.771,4.802 0.615,0.198 10 false 13 4.156,5.385 4.771,5.583 0.615,0.198 10 false 14 3.729,4.677 4.344,4.875 0.615,0.198 10 false MIC+ 3.76,5.458 4.375,5.656 0.615,0.198 10 false MIC- 2.979,6.646 3.479,6.844 0.5,0.198 10 false H82 2.979,6.802 4.76,7.177 1.781,0.375 10 false Navigation ECU 0.313,6.677 2.094,7.052 1.781,0.375 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the H81 radio and display receiver assembly connector.


b.

Disconnect the H82 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H81-25 (MCO+) - H82-13 (MIC+) Always Below 1 Ω
H81-26 (MCO-) - H82-14 (MIC-) Always Below 1 Ω
H81-25 (MCO+) or H82-13 (MIC+) - Body ground Always 10 kΩ or higher
H81-26 (MCO-) or H82-14 (MIC-) - Body ground Always 10 kΩ or higher
H81-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)
a.

Disconnect the H82 navigation ECU connector.


b.

Turn the ignition switch to ACC.


c.
E368005C58
1.5,0.427 1.917,0.677 0.417,0.25 1.75,2.083 1.292,1.469 false 0.833,2.083 1.188,1.469 false 2.813,3.427 3.208,3.656 0.396,0.229 10 false GND 0.656,2.115 1.052,2.344 0.396,0.229 10 false MIC+ 0.167,0.135 0.563,0.365 0.396,0.229 10 false *a 1.583,0.469 1.979,0.698 0.396,0.229 10 false H82 1.646,2.115 2.042,2.344 0.396,0.229 10 false MIC-
*a Front view of wire harness connector
(to Navigation ECU)


Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H82-13 (MIC+) - H82-14 (MIC-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the V7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-25 (SNS2) - V7-13 (SNS2) Always Below 1 Ω
H80-23 (MACC) - V7-16 (MACC) Always Below 1 Ω
H80-21 (MIN+) - V7-15 (MCO+) Always Below 1 Ω
H80-22 (MIN-) - V7-14 (MCO-) Always Below 1 Ω
H80-25 (SNS2) or V7-13 (SNS2) - Body ground Always 10 kΩ or higher
H80-23 (MACC) or V7-16 (MACC) - Body ground Always 10 kΩ or higher
H80-21 (MIN+) or V7-15 (MCO+) - Body ground Always 10 kΩ or higher
H80-22 (MIN-) or V7-14 (MCO-) - Body ground Always 10 kΩ or higher
H80-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the H80 radio and display receiver assembly connector.


b.

Connect the V7 map light assembly connector.


c.
C433402C01
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 true 2.188,2.885 1.927,2.146 true 2.813,2.604 2.052,2.156 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.594,0.771 1.906,0.969 0.313,0.198 10 false H80 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.094,2.896 2.729,3.115 0.635,0.219 10 false MACC 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H80-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-24 (SGND) - Body ground Always Below 1 Ω
H80-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

7.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the H80 radio and display receiver assembly connector.


b.

Connect the V7 map light assembly connector.


c.

Turn the ignition switch to ACC.


d.
E437720C01
1.51,0.146 1.885,0.396 0.375,0.25 0.656,1.906 1.125,1.219 true 1.208,1.917 1.219,1.219 true 0.427,1.948 1.042,2.146 0.615,0.198 10 false MCO+ 1.615,0.198 2.229,0.396 0.615,0.198 10 false V7 2.958,3.25 3.406,3.438 0.448,0.188 10 false GND 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a 1.104,1.958 1.719,2.156 0.615,0.198 10 false MCO-
*a Component with harness connected
(Map Light Assembly)


Connect an oscilloscope to terminals 15 (MCO+) and 14 (MCO-) of the V7 map light assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V7-15 (MCO+) - V7-14 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

8.INSPECT MAP LIGHT ASSEMBLY
8.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the MC telephone microphone assembly connector.


c.
E437721C02
1.458,0.396 1.844,0.646 0.385,0.25 1.5,2.823 1.885,3.073 0.385,0.25 1.813,2.146 1.385,1.635 true 1.427,2.125 1.167,1.615 true 0.448,2.073 0.969,1.615 true 0.99,2.167 1.073,1.625 true 1.146,3.823 1.427,3.406 true 1.552,3.813 1.563,3.406 true 2,3.823 1.698,3.417 true 2.469,3.656 2.01,3.406 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.125,2.458 0.458,2.656 0.333,0.198 10 false *b 1.354,2.198 1.854,2.417 0.5,0.219 10 false MCO- 0.896,2.198 1.375,2.406 0.479,0.208 10 false MCO+ 1.573,0.458 2.052,0.667 0.479,0.208 10 false V7 1.604,2.885 2.083,3.094 0.479,0.208 10 false MC 1.823,2.188 2.302,2.396 0.479,0.208 10 false SNS2 0.25,2.125 0.75,2.344 0.5,0.219 10 false MACC 2.49,3.708 2.969,3.917 0.479,0.208 10 false MACC 1.958,3.865 2.438,4.073 0.479,0.208 10 false MIC+ 1.479,3.875 1.958,4.083 0.479,0.208 10 false MIC- 1,3.865 1.479,4.073 0.479,0.208 10 false SNS2
*a Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-13(SNS2) - MC-1(SNS2) Always Below 1 Ω
V7-16(MACC) - MC-5(MACC) Always Below 1 Ω
V7-15(MCO+) - MC-3(MIC+) Always Below 1 Ω
V7-14(MCO-) - MC-2(MIC-) Always Below 1 Ω
V7-13(SNS2) - Body ground Always 10 kΩ or higher
V7-16(MACC) - Body ground Always 10 kΩ or higher
V7-15(MCO+) - Body ground Always 10 kΩ or higher
V7-14(MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY