Home › General › SPECIFICATIONS › M15A-FKS ENGINE CONTROL
RM36W0E _V1 General _087262 SPECIFICATIONS _0422197 M15A-FKS ENGINE CONTROL F

SPECIFICATIONS  M15A-FKS ENGINE CONTROL  SERVICE DATA  


IGNITION SYSTEM
Standard Insulation Resistance Spark plug (terminal part) - Body ground 10 MΩ or higher
Spark Plug Type DENSO made FC16HR-Q8
NGK made DILKAR6T8
Maximum Electrode Gap for Used Spark Plug 1.2 mm (0.0472 in.)
Standard Electrode Gap for New Spark Plug 0.7 to 0.8 mm (0.0276 to 0.0315 in.)

CAMSHAFT OIL CONTROL VALVE (for Intake Side)
Standard Stroke 4.5 mm (0.177 in.) or more

CAMSHAFT OIL CONTROL VALVE (for Exhaust Side)
Standard Stroke 2.2 mm (0.0866 in.) or more

CAMSHAFT OIL CONTROL SOLENOID (for Intake Side)
Standard Resistance 1 - 2 0 °C (32 °F) 5.3 to 6.3 Ω
20 °C (68 °F) 5.8 to 6.8 Ω
40 °C (104 °F) 6.2 to 7.4 Ω
Stroke Amount Standard 6.5 mm (0.256 in.) or more

CAMSHAFT OIL CONTROL SOLENOID (for Exhaust Side)
Standard Resistance 1 - 2 0 °C (32 °F) 6.3 to 7.3 Ω
20 °C (68 °F) 6.9 to 7.9 Ω
40 °C (104 °F) 7.4 to 8.6 Ω
Stroke Amount Standard 4.3 mm (0.169 in.) or more

THROTTLE BODY
Standard Resistance 5 (M-) - 6 (M+) 20°C (68°F) 0.3 to 100 Ω

ACCELERATOR PEDAL
Standard Voltage Accelerator Position Sensor No.1 Voltage Accelerator pedal fully released 0.5 to 1.1 V
Accelerator pedal fully depressed 2.6 to 4.5 V
Accelerator Position Sensor No.2 Voltage Accelerator pedal fully released 1.2 to 2.0 V
Accelerator pedal fully depressed 3.4 to 4.75 V

ENGINE COOLANT TEMPERATURE SENSOR
Standard Resistance 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.310 to 0.326 kΩ

KNOCK SENSOR
Standard Resistance 25°C (77°F) 120 to 280 kΩ

AIR FUEL RATIO SENSOR (for Sensor 1)
Standard Resistance 4 (HA1A) - 5 (+B) 20°C (68°F) 2.5 to 3.0 Ω
1 (IP+) - 3 (VS+) Always 1 MΩ or higher

AIR FUEL RATIO SENSOR (for Sensor 2)
Standard Resistance 1 (HA1B) - 2 (+B) 20°C (68°F) 2 to 6 Ω
1 (HA1B) - 4 (A1B-) Always 10 kΩ or higher

RELAY
Standard Resistance
(No. 1 Electronic Fuel Injection Main Relay (EFI-MAIN NO. 1))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(No. 2 Electronic Fuel Injection Main Relay (EFI-MAIN NO. 2))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(No. 3 Electronic Fuel Injection Main Relay (EFI-MAIN NO. 3))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Injection Relay (D INJ))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Air Fuel Ratio Sensor Heater Relay (A/F HTR))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(No. 1 Ignition Relay (IGP))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω