Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM36W0E _56 Audio / Visual / Telematics _088616 NAVIGATION / MULTI INFO DISPLAY _0422142 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna malfunction
·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

Radio and display receiver assembly


B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna power source malfunction
·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E362443E34
5.115,3.146 6.854,3.729 1.74,0.583 10 false Radio and Display Receiver Assembly 0.583,1.26 2.625,1.677 2.042,0.417 10 false Navigation Antenna Assembly 0.417,3 4.104,3.344 3.688,0.344 10 false *: Antenna Cord Sub-assembly 0.594,1.104 1.156,1.438 0.563,0.333 10 false GS 5.115,2.948 5.677,3.281 0.563,0.333 10 false GP 4.958,0.5 5.417,0.875 0.458,0.375 10 false 1 1.844,0.49 2.302,0.865 0.458,0.375 10 false 3 3.406,1.24 3.844,1.594 0.438,0.354 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Check that the antenna cord sub-assembly cable is properly installed and does not have any sharp bends, pinching or loose connections before performing following procedure.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

B

3.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.

Remove the antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E322997C20
0.5,1.188 0.917,1.438 0.417,0.25 0.656,3.479 1.073,3.729 0.417,0.25 1.927,3.74 2.344,3.323 true 1.854,1 2.271,0.583 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.354,3.177 2.667,3.375 0.313,0.198 10 false 1a 2.313,0.427 2.625,0.625 0.313,0.198 10 false 3a 0.604,1.229 0.917,1.427 0.313,0.198 10 false GS 0.771,3.521 1.083,3.719 0.313,0.198 10 false GP
*a Component without harness connected
(Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GS-3 - GP-1 Always Below 1 Ω
GS-3a - GP-1a Always Below 1 Ω
GS-3 or GP-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NAVIGATION ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

4.INSPECT NAVIGATION ANTENNA ASSEMBLY

b.
E381436C29
1.219,1.177 1.615,0.771 true 1.115,1.198 1.427,1.396 0.313,0.198 10 false 3a 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Navigation Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 3a Always 50 to 500 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG