Home › Vehicle Interior › HEATING / AIR CONDITIONING › SOLAR SENSOR
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0424507 SOLAR SENSOR G

HEATING / AIR CONDITIONING  SOLAR SENSOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89120A 1.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

a.

Check the wire harness.

i.

Disconnect the automatic light control sensor.


ii.
E393536C08
1.531,0.25 1.906,0.521 0.375,0.271 0.906,1.688 1.406,1.188 true 1.635,1.698 1.615,1.208 true 0.354,0.26 0.667,0.417 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 11 false H78 1.479,1.719 2.094,1.917 0.615,0.198 10 false CLTE 0.708,1.719 1.323,1.917 0.615,0.198 10 false CLTB
*a Front view of wire harness connector
(Automatic Light Control Sensor (Solar Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H78-1 (CLTB) - H78-2 (CLTE) IG ON 11 to 14 V


If the specified condition is not met, replace the vehicle wire harness.



b.

Check the resistance.

i.
E393536C09
1.521,0.25 1.917,0.51 0.396,0.26 1.635,1.698 1.615,1.208 true 0.354,0.26 0.667,0.417 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 11 false H78 1.479,1.719 2.094,1.917 0.615,0.198 10 false CLTE
*a Front view of wire harness connector
(Automatic Light Control Sensor (Solar Sensor))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H78-2 (CLTE) - Body ground Always Below 1 Ω


If the specified condition is not met, replace the vehicle wire harness.



c.

Check the automatic light control sensor.

i.

Connect the automatic light control sensor.


ii.

Check the waveform. Use the oscilloscope and check the waveform in the terminal spaces.

NOTICE:

With the connector connected as is, check from the rear side of the connector.


E393537C05
1.688,0.792 2.104,0.979 0.417,0.188 1.156,2.094 1.656,1.677 true 2.323,2.083 1.99,1.667 true 0.521,0.677 0.833,0.833 0.313,0.156 10 false *a 3.5,0.677 3.813,0.833 0.313,0.156 10 false *b 1.781,0.813 2.24,1.01 0.458,0.198 10 false H78 6.375,2.083 6.833,2.281 0.458,0.198 10 false GND 0.958,2.115 1.406,2.313 0.448,0.198 10 false CLTS 2.208,2.115 2.656,2.313 0.448,0.198 10 false CLTE
*a Component with harness connected
(Automatic Light Control Sensor (Solar Sensor))
*b Waveform


OK:
Tester Connection Condition Tool Setting Specified Condition
H78-4 (CLTS) - H78-2 (CLTE) IG ON 2V/DIV.,10ms/DIV. Pulse generation
(See waveform)


HINT:

The communication waveform changes according to the surrounding brightness.


If the result is not as specified, the automatic light control sensor may be malfunctioning.