Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM36W0E _59 Vehicle Exterior _088063 WIPER / WASHER _0424526 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85143R 1.INSTALL REAR WIPER MOTOR GROMMET

a.
E427636C02
1.385,0.5 1.74,1.104 1.74,1.104 2.083,0.51 true 1.667,1.135 1.979,1.292 0.313,0.156 10 false *a
*a Rear Wiper Motor Grommet Lip
V100145

MP grease


Apply MP grease to the entire surface of the rear wiper motor grommet lip.

HINT:

Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



b.
E427637C02
1.771,0.958 2.156,0.552 true 2.219,0.469 2.531,0.667 0.313,0.198 10 false *a
*a Alignment Mark


Install the rear wiper motor grommet.

HINT:

Install the rear wiper motor grommet with its alignment mark facing up.



Hide 85110R 2.INSTALL REAR WIPER MOTOR ASSEMBLY

a.

Install the rear wiper motor assembly with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the connector.


Hide 67761A 3.INSTALL BACK DOOR TRIM COVER

Hide 67751 4.INSTALL BACK DOOR TRIM BOARD

Hide 5.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.

When reusing the rear wiper arm and blade assembly:

i.
E358655C06
1.031,1.073 1.615,1.073 true 1.813,3.104 2.25,3.333 true 0.833,1 1.146,1.198 0.313,0.198 10 false *a 2.323,3.26 2.635,3.458 0.313,0.198 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the rear wiper motor assembly:

i.

Clean the wiper pivot serrations with a wire brush.

NOTICE:

Do not grind down the wiper pivot serrations.




c.

Turn the ignition switch on.


d.

Operate the rear wiper motor assembly and stop it at the automatic stop position.


e.

Turn the ignition switch off.


f.
E427638C03
1.594,2.552 1.854,2.75 true 1.292,2.292 1.406,2.469 0.115,0.177 10 true A 1.885,2.76 2.083,2.938 0.198,0.177 10 true *a 1.281,2.594 1.396,2.771 0.115,0.177 10 true A
*a Alignment Mark


Install the rear wiper arm and blade assembly with the nut to the position shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the rear wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 20 mm (0.787 in.)



g.

Turn the ignition switch on.


h.

Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not contact the vehicle body.


i.

Turn the ignition switch off.


Hide 85292A 6.INSTALL REAR WIPER ARM HEAD CAP

a.

Engage the claws to install the rear wiper arm head cap as shown in the illustration.

E427657C02
0,0 0,0 false
V113147

Install in this Direction - -