Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › COMBINATION SWITCH
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424595 COMBINATION SWITCH G

HYBRID / BATTERY CONTROL  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT COMBINATION SWITCH ASSEMBLY

a.

Inspect EV mode switch

i.
C401666C33
1.521,0.146 1.896,0.365 0.375,0.219 2.083,1.417 2.479,1.927 true 1.625,1.906 1.823,1.427 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 2.5,1.969 2.979,2.156 0.479,0.188 10 false E 1.531,1.958 2.052,2.135 0.521,0.177 10 false S 1.604,0.177 2.063,0.375 0.458,0.198 10 false H18
*a Component without harness connected
(Combination Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-6(S) - H18-5(E) EV mode switch being pushed and held Below 50 Ω
H18-6(S) - H18-5(E) EV mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the combination switch assembly.



b.

Inspect DRIVE mode switch

i.
C401666C34
1.521,0.146 1.896,0.365 0.375,0.219 2.083,1.417 2.479,1.927 true 1.188,1.885 1.385,1.406 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 2.5,1.969 2.979,2.156 0.479,0.188 10 false E 1.01,1.958 1.531,2.135 0.521,0.177 10 false DRV 1.604,0.177 2.063,0.375 0.458,0.198 10 false H18
*a Component without harness connected
(Combination Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-8(DRV) - H18-5(E) DRIVE mode switch being pushed and held Below 50 Ω
H18-8(DRV) - H18-5(E) DRIVE mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the combination switch assembly.



c.

Inspect illumination

i.
C401666C35
1.51,0.104 1.885,0.354 0.375,0.25 0.708,0.292 0.979,0.292 0.979,0.292 1.396,1.125 true 2.698,0.292 2.448,0.292 2.448,0.292 2.031,1.125 true 0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 0.365,0.208 0.979,0.406 0.615,0.198 10 false ILL+ 2.75,0.198 3.365,0.396 0.615,0.198 10 false ILL- 1.573,0.156 2.031,0.354 0.458,0.198 10 false H18
*a Component without harness connected
(Combination Switch Assembly)


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the combination switch assembly.

OK:
Tester Connection Specified Condition
Auxiliary Battery positive (+) - H18-4 (ILL+)
Auxiliary Battery negative (-) - H18-1 (ILL-)
Illuminates


If the result is not as specified, replace the combination switch assembly.