Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _089412 M15A-FXE ENGINE MECHANICAL _0424637 REAR CRANKSHAFT OIL SEAL A

M15A-FXE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 2.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A464394N01
1.042,1.073 0.552,1.073 0.552,1.073 0.813,0.646 false 0.229,1 0.688,1.198 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A464826

Remove the 6 bolts and transmission input damper assembly from the flywheel sub-assembly.


Hide 13405 3.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A464394N01
1.042,1.073 0.552,1.073 0.552,1.073 0.813,0.646 false 0.229,1 0.688,1.198 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.
A464825

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


Hide 19315 4.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A464827

Remove the No. 1 crankshaft position sensor plate.


Hide 11401L 5.REMOVE REAR ENGINE OIL SEAL

a.
A464828C01
2.99,1.458 3.177,0.771 true 1.896,1.406 1.625,1.083 true 2.917,1.49 3.229,1.688 0.313,0.198 10 false *b 1.917,1.448 2.135,1.646 0.219,0.198 10 true *a
*a Protective Tape
*b Cut Position


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.


HINT:

Tape the screwdriver tip before use.