Home › Power Source / Network › M15A-FKS (BATTERY / CHARGING) › GENERATOR (for 80A Type)
RM36W0E _57 Power Source / Network _087763 M15A-FKS BATTERY / CHARGING _0424751 GENERATOR(for 80A Type) A

M15A-FKS BATTERY / CHARGING  GENERATOR(for 80A Type)  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A399041

Remove the generator pulley cap from the generator pulley with clutch.

NOTICE:
·

Do not reuse the generator pulley cap.

·

If the generator pulley cap is removed, replace the generator pulley cap and generator pulley with clutch with new ones as the correct grease amount cannot be confirmed.



HINT:

Although grease will be observed when the generator pulley cap is removed, this does not indicate a malfunction.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.
A284135E16
1.354,0.646 1.052,0.354 1.052,0.354 0.813,0.354 false 2.344,0.875 2.073,0.875 2.073,0.875 1.76,1.417 false 0.271,0.281 0.854,0.531 0.583,0.25 10 false SST (A) 2.438,0.792 2.99,1.063 0.552,0.271 10 false SST (B)

Install SST (A) to SST (B) as shown in the illustration.

SST
09820-63021  


c.
A399042C06
1.719,0.219 1.865,0.219 1.865,0.219 2.125,0.552 true 1.573,1.031 1.708,1.479 1.708,1.479 1.885,1.479 true 3.042,1.594 3.042,0.927 true 1.573,0.125 1.885,0.281 0.313,0.156 10 false *a 1.927,1.427 2.51,1.667 0.583,0.24 10 false SST (A) 2.833,1.615 3.365,1.802 0.531,0.188 10 false SST (A)
*a Rotor Shaft


Fit the rotor shaft end into SST (A).


d.
A399043C05
1.792,0.104 1.969,0.104 1.969,0.104 2.323,0.344 true 2.01,1.542 1.885,1.542 1.885,1.542 1.448,1.094 false 3.021,1.635 3.021,1.115 true 1.646,0.01 1.958,0.167 0.313,0.156 10 false *1 2.042,1.479 2.813,1.677 0.771,0.198 10 false SST (B) 2.844,1.656 3.417,1.865 0.573,0.208 10 false SST (B)
*1 Generator Pulley with Clutch


Fit SST (B) to the generator pulley with clutch.


e.
A399044C04
1.917,0.74 2.198,0.323 2.198,0.323 2.333,0.323 false 2.125,0.938 2.385,0.583 2.385,0.583 2.521,0.583 false 1.708,1.979 1.875,2.125 0.167,0.146 10 true *a 0.75,1.969 1.063,2.125 0.313,0.156 10 false *b 2.583,0.5 3.354,0.698 0.771,0.198 10 false SST (A) 2.385,0.24 3.156,0.438 0.771,0.198 10 false SST (B)
*a Hold
*b Turn


Loosen the generator pulley with clutch by turning SST (B) as shown in the illustration.

NOTICE:
·

Check that the generator drive end frame is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.




f.

Remove SST (A) and (B) from the generator pulley with clutch.


g.

Remove the generator pulley with clutch from the rotor shaft.


h.

Remove the generator drive end frame from the vise.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.
A399045

Place the generator assembly on the generator pulley with clutch.


b.
A399046

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 27387B 4.REMOVE GENERATOR TERMINAL INSULATOR

a.
A399047

Remove the generator terminal insulator from the generator coil assembly.


Hide 27370 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A399048

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A399049

Remove the 4 bolts.


b.
A399050C01
2.073,0.823 2.479,0.823 false 0.594,1.677 0.99,2.01 0.99,2.01 1.156,2.01 true 0.604,0.635 0.917,0.792 0.313,0.156 10 false *a 2.552,0.49 2.865,0.646 0.313,0.156 10 false *b 2.5,0.74 2.948,0.917 0.448,0.177 10 false SST 1.177,1.938 1.625,2.115 0.448,0.177 10 false SST
*a Hold
*b Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


c.
A401900

Remove the bearing cover packing.

NOTICE:

If the bearing cover packing breaks, remove the broken pieces completely.


HINT:

The bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A401886C01
0.635,0.427 0.813,0.427 0.813,0.427 1.146,0.76 false 2.188,1.844 2.656,2 2.656,2 2.813,2 false 0.49,0.333 0.802,0.49 0.313,0.156 10 false *1 2.833,1.906 3.146,2.063 0.313,0.156 10 false *2
*1 Generator Rotor Assembly
*2 Generator Drive End Frame


Remove the generator rotor assembly.

NOTICE:

Do not drop the generator rotor assembly.



Hide 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A401887

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A401888N01
1.167,1.156 2.031,1.635 2.031,1.635 1.115,1.344 true 2.063,1.563 2.521,1.76 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60011  (09951-00250)
09950-70010  (09951-07100)