The light control LED ECU supplies internally boosted voltage to the light control LED ECU LH so that the current supplied to the LED is always maintained at a constant value.
These DTCs are also output when the main body ECU (multiplex network body ECU) detects malfunctions while monitoring the applied voltage.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B243900 | Headlight LH Circuit | Detection condition:
Ignition switch is to ON, low beam headlights illuminated Malfunction status:
·
LED (LED) malfunction ·
Open/short in LED (LEG) circuit Malfunction duration:
10 seconds or more |
·
Headlight unit assembly LH ·
Harness or connector ·
Light control LED ECU LH |
| B243A00 | Headlight RH Circuit | Detection condition:
Ignition switch is to ON, low beam headlights illuminated Malfunction status:
·
LED (LED) malfunction ·
Open/short in LED (LEG) circuit Malfunction duration:
10 seconds or more |
·
Headlight unit assembly RH ·
Harness or connector ·
Light control LED ECU RH |
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| B243900 and B243A00 are not output | A |
| B243900 is output | B |
| B243A00 is output | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Interchange the headlight unit assembly LH with RH and connect the connectors to them.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B243900 is output | A |
| DTC B243A00 is output | B |
A
B
| *a | Front view of wire harness connector
(Light Control LED ECU LH) |
| *b | Front view of wire harness connector
(Headlight Unit Assembly LH) |
Remove the headlight unit assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
Remove the wire harness.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A - [1] - B - [16] | Always | Below 1 Ω |
| A - [3] - B - [5] | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the headlight unit assembly RH with LH and connect the connectors to them.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B243A00 is output | A |
| DTC B243900 is output | B |
A
B
| *a | Front view of wire harness connector
(Light control LED ECU RH) |
| *b | Front view of wire harness connector
(Headlight Unit Assembly RH) |
Remove the headlight unit assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
Remove the wire harness.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A - [1] - B - [16] | Always | Below 1 Ω |
| A - [3] - B - [5] | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG