Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0424966 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  TERMINALS OF ECU  


CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E434509C13
4.417,3.24 4.802,3.469 0.385,0.229 1.521,4.5 1.906,4.729 0.385,0.229 3.875,4.5 4.26,4.729 0.385,0.229 5.698,4.5 6.083,4.729 0.385,0.229 1.146,6.104 1.531,6.333 0.385,0.229 2.938,6.104 3.323,6.333 0.385,0.229 4.25,6.104 4.635,6.333 0.385,0.229 3.438,7.781 3.823,8.01 0.385,0.229 2.135,1.385 2.521,1.615 0.385,0.229 2.135,1.771 2.521,2 0.385,0.229 2.292,3.24 2.677,3.469 0.385,0.229 3.792,0.292 4.177,0.521 0.385,0.229 5.26,6.104 5.646,6.333 0.385,0.229 6.26,6.104 6.646,6.333 0.385,0.229 2.01,0.698 2.333,0.427 false 1.396,0.521 1.719,0.25 false 0.969,1.885 1.281,2.083 0.313,0.198 10 false 4H 1.167,2.385 1.479,2.583 0.313,0.198 10 false 4F 0.979,1.083 1.292,1.281 0.313,0.198 10 false 4E 0.979,1.594 1.292,1.792 0.313,0.198 10 false 4D 6.052,2.094 6.365,2.292 0.313,0.198 10 false 4A 2.229,1.438 2.688,1.635 0.458,0.198 10 false H5 2.229,1.813 2.688,2.01 0.458,0.198 10 false H4 3.896,0.333 4.281,0.521 0.385,0.188 10 false MB 2.417,3.292 2.885,3.5 0.469,0.208 10 false H4 4.531,3.292 4.99,3.49 0.458,0.198 10 false H5 3.052,6.146 3.51,6.344 0.458,0.198 10 false 4D 5.813,4.542 6.271,4.74 0.458,0.198 10 false 4A 3.542,7.813 4,8.01 0.458,0.198 10 false MB 2.385,0.354 2.698,0.552 0.313,0.198 10 false *2 6.031,1.729 6.344,1.927 0.313,0.198 10 false 4B 6.031,1.146 6.344,1.344 0.313,0.198 10 false 4C 0.969,2.146 1.281,2.344 0.313,0.198 10 false 4G 3.979,4.552 4.292,4.75 0.313,0.198 10 false 4B 1.635,4.542 1.948,4.74 0.313,0.198 10 false 4C 1.26,6.135 1.573,6.333 0.313,0.198 10 false 4E 4.365,6.146 4.677,6.344 0.313,0.198 10 false 4H 5.354,6.146 5.667,6.344 0.313,0.198 10 false 4G 6.375,6.146 6.688,6.344 0.313,0.198 10 false 4F 1.771,0.146 2.083,0.344 0.313,0.198 10 false *1
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


b.

Reconnect the power distribution box assembly connector.


c.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors connected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-13 (GND1) - Body ground Ground Always Below 1 Ω
MB-26 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
MB-27 (IGR) - Body ground IG power supply Ignition switch ON 11 to 14 V


d.

Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
4E-5 (FRCY) - Body ground Front door courtesy light switch (for RH) input Front door RH open Below 1 V
Front door RH closed 11 to 14 V
4E-3 (FLCY) - Body ground Front door courtesy light switch (for LH) input Front door LH open Below 1 V
Front door LH closed 11 to 14 V
4E-1 (RCTY) - Body ground Rear door courtesy light switch (for RH) input Rear door RH open Below 1 V
Rear door RH closed Pulse generation
4E-26 (LCTY) - Body ground Rear door courtesy light switch (for LH) input Rear door LH open Below 1 V
Rear door LH closed Pulse generation
4E-2 (BCTY) - Body ground Back door courtesy light switch input Back door closed Below 1 V
Back door open 11 to 14 V
4E-39 (TR+) - Body ground Back door lock motor drive output Back door closed → open Below 1 V → 11 to 14 V → Below 1 V
4E-37 (ACT-) - Body ground Door lock motor unlock drive output Door control switch or driver door key cylinder off → on (unlock) Below 1 V → 11 to 14 V → Below 1 V
4E-36 (ACT-) - Body ground
4C-36 (ACT-) - Body ground
4B-34 (ACT+) - Body ground Door lock motor lock drive output Door control switch or driver door key cylinder off → on (lock) Below 1 V → 11 to 14 V → Below 1 V
4B-19 (ACT+) - Body ground
4E-14 (ACT+) - Body ground
H4-3 (LSFR) - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V
Front door RH locked Pulse generation
H4-9 (LSFL) - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V
Front door LH locked Pulse generation
H5-23 (LSWR) - Body ground Rear door RH unlock detection switch input Rear door RH unlocked Below 1 V
Rear door RH locked Pulse generation
H4-10 (LSWL) - Body ground Rear door LH unlock detection switch input Rear door LH unlocked Below 1 V
Rear door LH locked Pulse generation
H4-28 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
H4-28 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder not turned Pulse generation
H4-4 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
H4-4 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder not turned Pulse generation
4D-7 (BZR) - Body ground Wireless door lock buzzer output Ignition switch off, all doors closed, electrical key transmitter sub-assembly no inside vehicle and lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed (wireless door lock buzzer answer-back) Below 1 V → Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B574584N04
4.76,0.5 5.26,0.75 0.5,0.25 3.396,0.5 3.896,0.75 0.5,0.25 1.948,0.5 2.448,0.75 0.5,0.25 4.896,0.552 5.354,0.75 0.458,0.198 10 false H46 3.521,0.552 3.979,0.75 0.458,0.198 10 false O47 2.073,0.552 2.531,0.75 0.458,0.198 10 false H45

a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H46-4 (E) - Body ground Ground Always Below 1 Ω
H46-29 (+B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the F44 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
O47-21 (RCO) - H46-4 (E) Output to smart door control receiver assembly
(Power supply for smart door control receiver assembly. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Proceed:
1.

The Ignition switch off

2.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 1)
O47-12 (CSEL) - H46-4 (E) Communication channel switching circuit
Proceed:
1.

The Ignition switch off

2.

Close all doors


No pulse generation → Pulse generation
O47-11 (RDAM) - H46-4 (E) Smart door control receiver assembly communication circuit
Proceed:
1.

The Ignition switch off

2.

All doors locked

3.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

4.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 2)


e.
B251178C12
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection O47-21 (RCO) - H46-4 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




f.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection O47-11 (RDAM) - H46-4 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed