Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0424966 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  B124296  Wireless Door Lock Tuner Component Internal Failure  


DESCRIPTION

The smart door control receiver assembly is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the smart door control receiver assembly. The smart door control receiver assembly receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (ex. If a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short to ground in RDAM terminal circuit between the certification ECU (smart key ECU assembly) and smart door control receiver assembly.

·

Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO


·

Wire harness or connector

·

Smart door control receiver assembly

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

E408228E05
1.25,1.198 1.865,1.396 0.615,0.198 10 false DATA 1.427,2.24 2.042,2.438 0.615,0.198 10 false +5 5.792,1.208 6.406,1.406 0.615,0.198 10 false RDAM 5.792,2.271 6.406,2.469 0.615,0.198 10 false RCO 5.813,3.052 6.427,3.25 0.615,0.198 10 false E 1.302,3.042 1.917,3.24 0.615,0.198 10 false GND 0.604,3.542 1.219,3.74 0.615,0.198 10 false O48 5.531,3.542 7.042,3.885 1.51,0.344 10 false Certification ECU (Smart Key ECU Assembly) 0.604,3.729 1.823,4.344 1.219,0.615 10 false Smart Door Control Receiver Assembly 1.719,1.219 2.333,1.417 0.615,0.198 10 false 5 1.708,2.24 2.323,2.438 0.615,0.198 10 false 4 1.708,2.927 2.323,3.125 0.615,0.198 10 false 1 5.448,3.042 6.063,3.24 0.615,0.198 10 false H46 5.448,1.313 6.063,1.51 0.615,0.198 10 false O47 5.448,2.365 6.063,2.563 0.615,0.198 10 false O47 5.49,1.104 6.104,1.302 0.615,0.198 10 false 11 5.479,2.833 6.094,3.031 0.615,0.198 10 false 29 5.49,2.167 6.104,2.365 0.615,0.198 10 false 21 0.75,1.813 0.938,2 0.188,0.188 10 false IC 6.229,0.813 6.469,1.01 0.24,0.198 10 false +B 6.25,1.833 6.49,2.031 0.24,0.198 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing or inspecting the smart door control receiver assembly and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the smart door control receiver assembly, the performance of the entry function and wireless function may be affected.

·

This DTC is not stored within 10 seconds of the ignition switch being turned from on to off.

·

Make sure that there are no electrical key transmitter sub-assemblies in the vehicle.



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the O48 smart door control receiver assembly connector.


b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B574584C02
4.76,0.5 5.26,0.75 0.5,0.25 3.396,0.5 3.896,0.75 0.5,0.25 1.948,0.5 2.448,0.75 0.5,0.25 3.302,2.104 3.604,1.271 true 4.083,2.094 3.708,1.365 true 4.979,2.094 4.604,1.365 true 4.896,0.552 5.354,0.75 0.458,0.198 10 false H46 3.521,0.552 3.979,0.75 0.458,0.198 10 false O47 2.073,0.552 2.531,0.75 0.458,0.198 10 false H45 3.969,2.125 4.427,2.323 0.458,0.198 10 false RCO 4.948,2.115 5.406,2.313 0.458,0.198 10 false E 3.094,2.135 3.604,2.375 0.51,0.24 10 false RDAM 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H46-29 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
O47-11 (RDAM) - H46-29 (E) Ignition switch off 11 to 14 V
O47-21 (RCO) - H46-29 (E) Always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals



Result:
Proceed to
OK
NG



OK

REPLACE SMART DOOR CONTROL RECEIVER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (SMART DOOR CONTROL RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (SMART DOOR CONTROL RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the O47 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O47-11(RDAM) - O48-5 (DATA) Always Below 1 Ω
O47-21 (RCO) - O48-4 (+5) Always Below 1 Ω
O48-1 (GND) - Body ground Always Below 1 Ω
O48-5 (DATA) or O47-11 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
O48-4 (+5) or O47-21 (RCO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR